Planet Networking & Communication VIP-101T Command Line Interface Manual Download Page 41

Page: 41 / 47

PLANET VIP-101T CLI configuration

- 35 -

a) -print

Parameter

–

print

is used to display current SUPPORT values configurations.

Syntax Description

This command has no arguments or keywords.

Default

This command has no default value.

–

fstart

Parameter

–

fstart

is used to enable or disable H.323 fast start mode. If you

’

d like to

enable H.323 fast start mode in VIP-101T, please make sure the destination call party

supports fast start mode as well.

Syntax Description

-fstart Enabled or disabled Fast start mode in VIP-101T, o to disable, 1 to enable this

feature..

Default

0 H.323 fast start mode is disabled.

–

tunnel

Parameter

–

tunnel

is used to enable or disable H.245 tunneling function.

Syntax Description

-tunnel Enabled or disabled H.245 Tunneling, 0 for disable and 1 for enable .

Default

0 H.245 tunnel mode is disabled.

d) -h245fs

Parameter

–

h245fs

is used to setup if VIP-101T opens H.245 separate channel after

H.323 fast start mode. (

support

–

h245fs 0/1

, 0 for open and 1 for not.)

Please make sure the destination call party supports this feature before applying this

parameter.

Summary of Contents for VIP-101T
















































Search results

Summary of Contents for VIP-101T

Reviews:

Related manuals for VIP-101T

Brands by name

Popular brands

Planet Networking & Communication VIP-101T, Command Line Interface Manual

Search results

Summary of Contents for VIP-101T

Reviews:

Related manuals for VIP-101T

Brands by name

Popular brands