background image

PLANET VIP-101T CLI configuration 

                                                                                                     

 

 

- 17 -

usr/config$ sysconf -print 
System information 
        DialPlan number of digits: 0 
        CallAlive auto-disconnection: Disabled 
        keypad DTMF type: H245SIGNALTYPE 
        H.450 features: Enabled 
        Inter-digit time out: 5 
        Digit type of end of dialing: [ # ] button 
 
usr/config$

 

 
 
12.[sysconf] command   

 

This command displays the system information and configuration.   

 

 

 

 

 

 

 

 

 

 

 

 

 

 

a) 

print 

Parameter -

print

 can display system overall information and configuration. 

 

Syntax Description 

This command has no arguments or keywords. 

 

Default

 

This command has no default value. 

 

Example 

 

 

 

 

 

 

 

 

b) 

plan 

System information and configuration 
Usage: 
sysconf [-plan digits] [-callalive flag] [-h450 flag] [-keypad type] [-idto time] [-eod type] 
sysconf -print 
        -print          Display system overall information and configuration. 
        -plan            Number of digits for dial plan. ( No or positive number 1 ~ 24. ) 
        -callalive Enable or disable auto-disconnection after 10 seconds not receiving packets 
from remote party. 
        -keypad        Select DTMF type. ( 0:INBAND, 1:H245ALPHANUMARIC, 
                              2:H245SIGNALTYPE, 3:Q931USERINFO. ) 
        -idto            The duration of two pressed digits in dial mode 
        -eod              Digit type of end of dialing. ( 0:No end of dialing, 
                              1:[OK] button, 2:[#} button, 3:[*] button. ) 
        -h450            Enable or disable H.450 related features. 
Example: 
        sysconf -plan 4 -callalive 0 -h450 1 -keypad 2 -idto 5 -eod 0 

Summary of Contents for VIP-101T
















































Reviews: