background image

2

 

General Description and Principle of Operation 

2.1

 

Function 

The

DVB-C  IT-19C  signal  Analyzer  is  designed  for

measuring

parameters  of  TV  channels  with 

analog modulation: video level, video level to sound level ratio, video level to noise level ratio. You 
can also measure power of TV channel with digital modulation. 

For  signals  of  DVB-C  and  J.83  Annex  B  digital  cable  television  standards,  the  Analyzer  allows  to 
measure parameters of reception quality — Modulation Error Ratio  (MER), Bit Error Ratio  (BER), 
the  number  of  wrong  MPEG  stream  packets,  the  noise  immunity  margin  (MARGIN),  and  the 
constellation diagram (on PC screen). 

IT-19C  provides  with  the  automatic  settings  detection  mode  (channel  frequency,  symbol  rate, 
modulation type). There is a spectrum analysis mode aimed at searching for any unwanted signal. 
The Analyzer can be connected to a PC for additional service modes. The Analyzer allows you to 
measure  the  direct  and  alternating  voltage  of  remote  distribution  receiving  systems  of  TV  and 
radio broadcasting network power supply. 

 

2.2

 

Environmental Conditions 

Normal operation conditions: 

1)

 

ambient temperature 

(23±5) ºС; 

2)

 

relative air humidity

(55±25)%; 

3)

 

atmospheric pressure 84-106 kPa (630-795 mm Hg); 

4)

 

voltage transmitters correspond to CAT.

 II

 installation category. 

Rated operation conditions: 

1)

 

ambient temperature   -10 to 5



°С; 

2)

 

relative air humidity 90% to 25 ºС temperature; 

3)

 

atmospheric pressure 84-106 kPa



630-795 mm Hg). 

2.3

 

Package Contents 

The Analyzer package includes: 

1)  The IT-19C Analyzer  ............................................................... 1 pc.; 

2)  Rubber boot  ........................................................................... 1 pc.; 

3)  Li-Po battery  .......................................................................... 1 pc.; 

4)  F-F RF adapter  ........................................................................ 1 pc.; 

5)  12V/1.2A charger  ................................................................... 1 pc.; 

Summary of Contents for IT-19C

































Reviews: