4
PIVOT CORPORATION
87-3, Shimookada Okada, Matsumoto-shi, Nagano, 390-0313 JAPAN
+
START
ENGINE
STOP
Troubleshooting
Switching The Display
Because after changing displays, if the car’ s engine is turned off within 3 seconds, the new
setting will not be stored, make sure to wait at least 3 seconds before turning the engine off.
Pl e a s e r e c o n f i r m w h e t h e r w i r i n g a n d
connections are correct or not.
Please reconfirm the Fitting List.
※
Our products have already been recognized as our Industrial Property or are in the process of receiving Industrial Property status.
※
We plan in the near future to take all possible legal measures to protect against unfair competition from look-alike products using similar designs, regulating characteristics,
circuitry and circuitry layout.
※
We strictly prohibit the unlicensed use of the PIVOT trademark and the unauthorized use of PIVOT User’s Manual.
Upon star ting up, the unit will not star t in the
newly changed display.
Poor connection of
Gauge cable
,
6-pin Connector
or
OBD Connector
wires.
Trouble
Possible Causes
Possible Solutions
Does not work with Engine start.
Illumination brightness settings
The unit has been installed into an incompatible
car model.
Before the opening demo starts the needle briefly moves.
This is due to a special characteristic of the meter and is not a malfunction.
The displayed values are different from the standard
meter.
Due to the ECU information received, the displayed values on this product may differ from those
of standard or other meters.
Each pressing will change the brightness
Adjustment in case of anxious about reflected illumination of door mirror
or something
[
c-1
= White,
c-2
= Orange ]
1
2
3
4
5
6
Press
the switch
for 6 seconds
Holding downs the switch
in operation
Display a peak value after
3 seconds and the current
brightness after 6 seconds
Press the switch
to change the brightness
(e.g.
L-3
)
Release the switch
after displayed
the current setting
Release
the switch
after setting is done
Setting Completed
Back to normal display with
no operation for 5 seconds
Illumination color settings
Each pressing will change the color.
1
2
3
4
5
Display the current
illumination color setting
Press the
switch to change
the color
(e.g.
c-1
)
Release the switch
after displayed
the current setting
Release the switch
after setting is done
Setting Completed
Back to normal display with
no operation for 5 seconds
1
4
5
2
3
●
When the engine starts, the needle will move to the extreme left several times
for searching position. Then it will move to the maximum value and finally to
reading for current measurement item.
●
Due to analyzation time for the car data transmission it may take up to a few
seconds from engine start before opening demo.(except wiring IGN)
Basic Operation
Opening
Demo
Display
Each Mode
Meter
OFF
Engine Start
Opening
Demo
Engine Stop
The needle stops
i n t h e v i c i n i t y of
lowest value.
●
Due to analyzation time for the car data transmission, the
illumination may remain on for up to 1 minutes even after the
engine has been turned off; this is normal and no effect on the
vehicle performance. (except wiring IGN)
Turning off
the Display
After the meter off,
Engine start during
pressing the switch
Engine Start
(High)
(Mid)
(Low)
Not displayed without temperature sensor.
Switching The Digital Display
Display and Reset the Peak Value
Water Temp
Oil Temp
Voltage
(Lighting)
(Lighting)
(Lighting)
(Blinking)
(Blinking)
(Blinking)
(decimal point
is lightning)
Real-time Display
Peak Value Display
Reset the Peak Value
Only the peak value on display will be reset. This will return
to the Real-time Display for the currently displayed mode.
Press
Switch
Press
Switch
Water Temperature / Oil Temperature
Reading the Display
for
3
Seconds
for
3
Seconds
With no operation
5
Seconds
●
Peak readings are reset when the key is turned OFF.
●
For Boost, Water Temperature and Oil Temperature the high will be shown and for Voltage the low will
be displayed.
●
If you wish to check the loss of voltage upon operation of the starter, turn the key to the ON position
and after the digital display comes on, operate the starter.
Press switch to change
the multi-digital display
in operation
The first place on the
below shows
“
-
”
(minus).
The third place from the
below shows
“
c
”
(Celsius).
Numerical Value
Only.
[
- 35
〜
-1°C ]
[
0
〜
99 °C ]
[
100
〜
150 °C ]
※
※
※
