5
Wiring
Chart
Wiring
Chart
Red
Gray
86
TOYOTA
車 名
年 式
H24.4
〜
BR-7
ブレーキ
ハーネス
品番
直接接続
接続番号
ブレーキ
ハーネス
接続色
製品のコード色
赤
灰
赤
灰
86
TOYOTA
車 名
年 式
H24.4
〜
BR-7
ブレーキ
ハーネス
品番
直接接続
接続番号
ブレーキ
ハーネス
接続色
製品のコード色
赤
灰
赤
灰
Wiring
Chart
OFF
The Wire color
of the product
1
2
Bef
o
re
Using
F
eatures
Connecting
The Wires
Installing
The Product
Initial
Settings
Ho
w to
Oper
ate
Speed Pulse
Settings
T
roub
le-
Shooting
(For more details , please refer to the brake harness manual.)
Gray
Red
To Brake Power (normal 12V)
Brake Switch
Connector
Brake
Pedal
Brake Switch (Brake Power and Brake Switch Signal)
Red
Red
Not Press Down
on Brake Pedal
Red
A
B
Gray
Brake
Switch
Brake
Switch
Ignition Switch
(12V with ignition
in the ON position)
Brake
Lamp
To Brake Switch Signal
Select a Wiring Method
Connect Directly
: Voltage Tester Lamp ON
: OFF
Gray
Gray
Brake Power
Brake Switch Signal
(12
V
)
(0
V
)
(12
V
)
(12
V
)
Press Down
on Brake Pedal
Brake
Lamp
Four Wires
IGN
Operation Signal
For a Two-Wire Connector
How to Test
(Refer to page 6, [How to use the Voltage Detector].)
For a Four(or more)-Wire Connector
When there are four(or more) wires, do not wire
to positions A and B as shown below. (See below
for how to check the voltage for each wiring position)
• After having completed the wiring confirm that the brake lamp
is working properly.
• There may be two or four(or more) wires
coming from the brake switch connec-
tor. Check the wiring position in the
“Wiring Char t ” and af ter testing the
voltage, carry out the wiring.
Connect Using Brake Harness (sold separately)
Connect the
Red and Gray
wires to the corresponding wire
colors found in the “Wiring Chart” .
e.g.) TOYOTA 86 (from Apr. 2012)
Switch
C
onnector
Wire leading
from product
(BR-7)
: Use Cut Connector
: Use Cut Connector
e.g. TOYOTA 86 (from Apr. 2012)
Connection
Numbers
2
黄
青
1
Connection
Colors
2
黄
青
1
Earth
Earth
1. Turn the ignition to the OFF. Please put gear into N (Neutral).
2. Check the terminal for each of the connections as designated in
the separate sheet “Wiring Chart” .
Select from either
“Connect Directly”
or
“Connect using
Brake Harness”
and carry out directions as stated.
1. After having tested voltage at the positions to be wired, connect as
directed.
2. In case of the car model which is blank of Wire Numbers or Brake
Harness Connection Color of “Wiring Chart” , please make sure to
carry out a voltage test and connect as directed.
Connect the Red and Gray wires to the corresponding
wire numbers found in the “Wiring Char t” using Cut
connector which is included.
(Refer to page 6 [Reference 2] “How to use the Cut Connectors” )
N o t e t h a t t h e c o l o r s li s t e d in t h e c h a r t u n d e r “ B r a ke
Harness Connection Color” are not the colors of the wires
on the car side.
Car Speed Signal
Orange
with earth
terminal
Earth
Black
Note: Painted screws and screws connected to plastic parts are
not ear thed; make sure to connect only to a place which is
earthed.
Note: Connect only to the cables on the car side as directed.
(Do not wire the speed signal to the CAN-BUS adaptor.)
Confirm the positions on the “ Wiring
Chart” and then connect.
(
⇒
Refer to page 6 [Reference 2] “How to use the Cut
Connectors” )
Fasten to a screw of a
metal par t which is
earthed.
1
3
2
4
Gray
Red
Note: If there are four(or more) wires, do not wire the remaining
(OFF 0V)
.
Accelerator
Accelerator
Accelerator
Passage of over
15
minutes
Accelerator
Connector
Disconnect
the connector
Controller
5 -pin
Connector
Connect to the side of
the unit.
Connect to the side of
the unit.
Connect to the side of
the unit.
Power Cable
8 -pin
Connector
Special Model Specific Harness
(sold separately)
6 -pin
Connector
Note: For details about connecting the Specialized Harness, please refer
to the user’ s manual that came with that harness.
Depending on the type of vehicle, if the connector is disconnected before the
ECU power is switched OFF the Check Engine Light may go on. (If the Light
comes on: Refer to page 12, “How to Turn Off the Check Engine Light” )
After inserting the connector, pull lightly to
make sure that it is securely locked.
Turn the ignition
to the OFF
position.
Only disconnect the accelerator connector after
having waited at least 15 minutes from the time
that the ignition was turned to the OFF position.
