background image

Section

5

No Diving or Jumping.  Observe all Safety Rules

5-7

Section

5

POOL MAINTENANCE

SPRINGTIME CLEANING OF YOUR POOL

PREPARING YOUR POOL IN THE SPRING CONTINUED

d.  When the pH and alkaline levels are ideal, apply a shock-treatment or chlorinate your water. Let it 

filter for 24 hours and again verify both the pH and free chlorine levels. NOTE: Add chemical 

products to your pool after sunset, as sunlight rapidly destroys chlorine.

e.  Let it filter for several days until the water is clear and the pH and free 

chlorine levels have stabilized. Add a conditioner/stabilizer by carefully 
following the manufacturer’s instructions. This will stop the chlorine from 
evaporating quickly in sunlight. Add the quantity of algicide required 
to prevent algae.

 

f.  You may now begin regular maintenance of your pool. Don’t 

forget to obtain a new set of solutions for your water analysis kit 
every spring. The old solutions may give false results.

g.  Make sure that the skimmer (screws and adapter) is 

properly in place and tighten the water return fittings to 

prevent leakage and premature rusting of the pool wall 
or the lower part of the bottom rail.

 

HAVE FUN!

IF YOU FOLLOW THESE TIPS AND ASK YOUR DEALER FOR ANY OTHER ADVICE YOU MAY NEED, 
YOU WILL HAVE ALL THE INFORMATION NECESSARY TO GET YOUR POOL OPERATING AGAIN.

Summary of Contents for V35048


















































Reviews: