Controls and displays
04
25
En
7
TV CONTROL buttons
These buttons are dedicated to control the TV assigned to
the
TV CTRL
button. Thus if you only have one TV to hook
up to this system assign it to the
TV CTRL
input source
button. If you have two TVs, assign the main TV to the
TV
CTRL
button (see page 67 for more on this).
TV
– Use to turn on/off the power of the TV.
TV VOL +/–
– Use to adjust the volume on your TV.
INPUT SELECT
– Use to select the TV input signal.
TV CH +/–
– Use to select channels.
8
Component control buttons
The main buttons (
,
, etc.) are used to control a
component after you have selected it using the input
source buttons.
The controls above these buttons can be accessed after
you have selected the corresponding input source button
(for example
DVD
,
DVR1
or
TV
). The following controls
can be accessed when listening to the built-in tuner:
MPX
– Switches between stereo and mono reception
of FM broadcasts. If the signal is weak then switching
to mono will improve the sound quality (page 32).
DISP
– Switches between named station presets and
radio frequencies (page 33).
9
STATUS
Press to check selected receiver settings (page 65).
10
MULTI OPE
Use this button to perform multi operations (page 69).
11
SHIFT
Press to access the controls outlined in white boxes (for
example,
INPUT SELECT
), or to display the currently
selected input source in the remote control LCD.
12
SOURCE
Press to turn on/off other components connected to the
receiver (see page 67 for more on this).
13 Character display (LCD)
This display shows information when transmitting
control signals.
The following commands are shown when you’re setting
the remote to control other components (see
Controlling
the rest of your system
on page 67):
SETUP
– Indicates the setup mode, from which you
choose the options below.
PRESET
– See
Selecting preset codes directly
on
page 67.
LEARNING
–
See
Programming signals from other
remote controls
on page 67.
MULTI OP
– See
Multi Operation and System Off
on
page 69.
SYS OFF
– See
Multi Operation and System Off
on
page 69.
DIRECT F
– See
Direct function
on page 69.
RENAME
– See
Renaming input source names
on
page 69.
ERASE
– See
Erasing one of the remote control button
settings
on page 68.
RESET
– See
Resetting the remote control presets
on
page 68.
READ ID
– See
Confirming preset codes
on page 68.
14 RECEIVER
Switches the remote to control the receiver (used to
select the green commands above the number buttons
(
ANALOG ATT
, etc.)). Also use this button to set up
surround sound (page 8, page 34). With
SHIFT
, this
selects the MULTI-ZONE control (page 55).
15 VOL +/–
Use to set the listening volume.
16 MUTE
Mutes the sound or restores the sound if it has been
muted (adjusting the volume also restores the sound).
17 Receiver controls
SIGNAL SEL
– Use to select an input signal (page 29).
SB ch
– Use to select the surround/virtual back
channel mode (page 29).
STEREO/F.S.SURR
– Switches between the stereo
playback mode (page 28) and the Front Stage
Surround Advance mode (page 28).
THX
– Press to select a Home THX listening mode
(page 27).
STANDARD
– Press for Standard decoding and to
switch between the various
2
Pro Logic IIx and
Neo:6 options (page 26).
ADV.SURR
– Use to switch between the various
surround modes
(page 27).
18 PHASE
– Press to switch on/off Phase Control
(page 10).
MCACC
– Press to switch between MCACC presets
(page 29).
S.DIRECT
– Press to select the Auto Surround mode
(page 26) or the Stream Direct mode (page 28).
Stream Direct playback bypasses the tone controls
and any other signal processing for the most
accurate reproduction of a source (page 28).
VSX-9120TXH_KU.book 25 ページ ２００７年４月１２日 木曜日 午前１１時４７分
