Pioneer PDP-R06C Service Manual Download Page 41

Page: 41 / 90

PDP-R06G

7. GENERAL INFORMATION

7.1 DIAGNOSIS

7.1.1 TROUBLESHOOTING

Image for the composite or S or TV signal is not displayed

Image for the composite or
S signal is not displayed

Is the function corresponding
to selected signal input
selected?

No Select the corresponding

signal with the Input selector.

Is the Component Signal is
connect to jack?
(Input 1, Input 2)

Disconnect Component and
confirm again.

Yes

Which signal is not output,
main or sub signal?

Yes

Is the HDMI Input is set to
disable? (Input 3)

No Set the HDMI Input set to

disable and confirm again.

Has the signal arrived
at IC4804?

Check the contact between
the pin jack and IC4804.

Yes

Is a signal output from
IC4804?
(pin 47) (pin 49)

Check around IC4804 and
check the communications
between IC4804 and the
microcomputer.

Main signal

Is a signal output from
IC4804?
(pin 42) (pin 45)

Has the signal arrived at
IC6001?
(pin 1) (pin 2)

Sub signal

Has the signal arrived at
IC6003?
(pin 148) (pin 158)

Check the communications
between IC4804 and IC6003.

Yes

Check the communications
between IC4804 and IC6001.

• For check the communication with the microcomputer,

refer to the section 6.3 SERVICE FACTORY MODE.

• The encircled numbers denote measuring point in the

Waveforms for Troubleshooting.

• Diagnosis points

Note:

Is the communication
between each IC on the MR
MAIN Assy and the
microcomputer normal?

Check around the IC that is
found to have a failure in
communication and the
microcomputer.

Yes

Has the symptom been
settled when the MR MAIN
Assy is replaced?

The panel is defective.

Yes

Finishing troubleshooting

Yes

TV signal is not displayed
on the screen.

Is the Input selector set to
TV?

Set the Input selector to TV.

Yes

Has the signal arrived
at IC4804?
(pin 57)

Check around the FE and
check the communications
between FE and IC4804 and
the microcomputer.

Yes

MR MAIN ASSY

Summary of Contents for PDP-R06C



























































































Search results

Summary of Contents for PDP-R06C

Reviews:

Related manuals for PDP-R06C

Brands by name

Popular brands

Pioneer PDP-R06C, Service Manual

Search results

Summary of Contents for PDP-R06C

Reviews:

Related manuals for PDP-R06C

Brands by name

Popular brands