Pioneer PDP-R06C Service Manual Download Page 54

Page: 54 / 90

PDP-R06G

7.2.2 POWER ON SEQUENCE

: The signal from the remote control unit (or a key signal) is input to the IF microcomputer.

: The IF microcomputer supplies the power to the main microcomputer and MOD microcomputer.

: The IF microcomputer transmits operation data from the remote control unit (or keys) to the main microcomputer.

: The main microcomputer issues a startup command to the MOD microcomputer.

: The MOD microcomputer controls the relay of the PDP Power MOD and starts the power-on sequence of the PDP.

: The main microcomputer controls the relay of the MR Power MOD and starts the power-on sequence of the MR.

MOD

Microcomputer

Power MOD
RELAY Control

BUFF

REM_B

PDP

BUFF

IC7203

BUFF

IC7201

BUFF

IC7203

BUFF

Power MOD
RELAY Control

Power MOD
STB Control

REM
infrared
receiver

Keys on the

front panel

IF_UCOM

IC5002

MAIN_UCOM

IC5206

SR Circuit

Q7603-Q7606

Inverter

Q5001

PM_SW

IC4212

REM_B

KEY_AD2

STB_MT

MTXD
MRXD
REQ

ACTIVE

V+3_3V_UCOM

SR_IN

TXD_IF
RXD_IF
CE_IF
REQ_IF
BUSY_IF

Descriptions in a call-out are signal names for reference.
For wiring numbers on the PDP side, refer to the service manual for the PDP.

Summary of Contents for PDP-R06C



























































































Search results

Summary of Contents for PDP-R06C

Reviews:

Related manuals for PDP-R06C

Brands by name

Popular brands

Pioneer PDP-R06C, Service Manual

Search results

Summary of Contents for PDP-R06C

Reviews:

Related manuals for PDP-R06C

Brands by name

Popular brands