manualshive.com logo in svg

Pioneer ELITE VSX-LX505, Instruction Manual

The Pioneer ELITE VSX-LX505 is a top-of-the-line AV receiver that boasts impressive features and exceptional sound quality. With its user-friendly interface, navigating this receiver couldn't be easier. For your convenience, an Instruction Manual is available for free download from manualshive.com, ensuring you get the most out of your audio experience.

Share
Download
background image

203

Appendix

Speaker combinations (European, Australian and Asian models)

• 

Up to two powered subwoofers can be connected in either combination.

Speaker 

Channels

FRONT

CENTER

SURROUND

SURROUND  

BACK

HEIGHT 1

HEIGHT 2

Bi-AMP

 (*3)

ZONE 2

 (*3)

(ZONE 

SPEAKER)

ZONE 3

 (*3)

(ZONE 

SPEAKER)

2.1 ch

3.1 ch

4.1 ch

5.1 ch

6.1 ch (*1)

7.1 ch (*1)

2.1.2 ch (*2)

 (*4) (*5)

 (*5)

 (*4)

3.1.2 ch (*2)

 (*4) (*5)

 (*5)

 (*4)

4.1.2 ch (*2)

 (*4) (*5)

 (*5)

 (*4)

5.1.2 ch (*2)

 (*4) (*5)

 (*5)

 (*4)

6.1.2 ch (*1)

7.1.2 ch (*1)

4.1.4 ch (*1)

5.1.4 ch (*1)

6.1.4 ch (*1)

 (*6)

7.1.4 ch (*1)

 (*6)

(*1)  The "Connecting an Integrated Amplifier (ZONE 3)" ( 

→

p72

) function cannot be used.

(*2)  When using Bi-AMP or ZONE 2 (ZONE SPEAKER), the "Connecting an Integrated Amplifier (ZONE 3)" ( 

→

p72

) function cannot be used. 

(*3)  The Bi-AMP and ZONE speakers cannot be used simultaneously.

(*4)  When using the ZONE 2 speakers, it is necessary to connect the height speakers to the SURROUND BACK terminal. 

(*5)  When using the Bi-AMP speakers, it is necessary to connect the Bi-AMP speakers to the HEIGHT 1 terminals, and the height speaker to the SURROUND BACK 

terminals.

(*6) 

Use an analog audio cable to connect the power amplifier to the PRE OUT SURROUND BACK jacks, then connect the surround back speakers to the power amplifier.

About the HEIGHT 1/HEIGHT 2

When connecting 2 sets of the height speakers, the combination of the height speakers that can be selected is as follows.

 

– Height 1 Speaker: Top Middle, Height 2 Speaker: Rear High

 

– Height 1 Speaker: Front High, Height 2 Speaker: One of Rear High/Top Middle/Top Rear/Dolby Enabled Speaker (Surround)/Dolby Enabled Speaker (Surround 

Back)

 

– Height 1 Speaker: Top Front or Dolby Enabled Speaker (Front), Height 2 Speaker: One of Rear High/Top Rear/Dolby Enabled Speaker (Surround)/Dolby Enabled 

Speaker (Surround Back)

When only 1 set of the height speakers is connected, 1 from the height speakers types can be selected.

Summary of Contents for ELITE VSX-LX505





















































































































































































































Reviews:

No comments

Related manuals for ELITE VSX-LX505

Hallicrafters Sky Champion S-20R Operating/Service Instructions preview
Sky Champion S-20R
Brand: Hallicrafters Pages: 5
Kathrein UFS 702si Notice D'Utilisation preview
UFS 702si
Brand: Kathrein Pages: 68
Kathrein UFS 601si Notice D'Utilisation preview
UFS 601si
Brand: Kathrein Pages: 48
Kathrein UFS 301Si Notice D'Utilisation preview
UFS 301Si
Brand: Kathrein Pages: 40
Kathrein UFD 505 Mode D'Emploi preview
UFD 505
Brand: Kathrein Pages: 61
Kathrein MSK 25 Instruction Manual preview
MSK 25
Brand: Kathrein Pages: 56
Kathrein CAP 210 Installation Manual preview
CAP 210
Brand: Kathrein Pages: 36
Kathrein Euroline UFE 341S Notice D'Utilisation preview
Euroline UFE 341S
Brand: Kathrein Pages: 36
NAD 3240PE Specifications preview
3240PE
Brand: NAD Pages: 2
Yamaha RX-V750 Service Manual preview
RX-V750
Brand: Yamaha Pages: 128
Yamaha RX-V2400 Service Manual preview
RX-V2400
Brand: Yamaha Pages: 147
Yamaha RX-V800 Service Manual preview
RX-V800
Brand: Yamaha Pages: 75
Axxera AV714BH Installation & Owner'S Manual preview
AV714BH
Brand: Axxera Pages: 32
PCB Piezotronics JM353B18 Installation And Operating Manual preview
JM353B18
Brand: PCB Piezotronics Pages: 17
Onkyo TX-8260 Instruction Manual preview
TX-8260
Brand: Onkyo Pages: 57
Sencor SCT 5051BMR User Manual preview
SCT 5051BMR
Brand: Sencor Pages: 17
Yaesu FT-2980R Operating Manual preview
FT-2980R
Brand: Yaesu Pages: 80
Radio Shack 19-1108 Owner'S Manual preview
19-1108
Brand: Radio Shack Pages: 11

Brands by name

Popular brands

Load more brands