Pioneer ELITE VSX-LX505 Instruction Manual Download Page 143

Page: 143 / 212

143

Setup

Hardware

Audio TV Out (Default Value: Auto)

You can enjoy audio through the speakers of the TV while this unit is on.

• This setting is fixed to "Auto" if you have set "Input/Output Assign" - "TV Out/

OSD" - "HDMI Out" or "HDMI" - "HDMI Out" in "AV Adjust" to "MAIN" or

"MAIN+SUB" and "HDMI CEC" is set to "On". If you change this setting, set

"HDMI CEC" to "Off".

•

Listening mode cannot be changed while "Audio TV Out" is set to "On" and

audio is being output from the TV.

•

Depending on your TV or input signal of the connected device, audio may not

be output from the TV even if this is set to "On". In such a case, audio is output

from the speakers of the unit.

•

Audio is output from this unit if you operate the MASTER VOLUME dial on this

unit when audio that is input to this unit is output from your TV speakers. If you

do not want to output audio, change the setting of this unit or TV, or reduce the

volume of this unit.

When this function is used

Off

When this function is not used

Auto

When the "HDMI Out" setting is "MAIN" or "MAIN+SUB" and

the "HDMI CEC" setting is "On", the setting is fixed to "Auto".

With "Auto", when audio is output from the TV speakers, audio

is not output from the speakers of this unit, and when audio is

output from the speakers of this unit, audio is not output from

the TV speakers.

•

If the HDMI CEC setting is off on the TV, there may be audio

output from both the TV speakers and the speakers of this

unit.

Audio Return Channel (eARC supported) (Default Value: On)

You can enjoy the sound of an HDMI-connected ARC-compatible TV or eARC-

compatible TV through the speakers connected to the unit.

When enjoying the TV sound through the speakers connected

to the unit

Off

When the ARC function or eARC function is not used

Auto Delay (Default Value: On)

Automatically corrects desynchronization between the video and audio signals

based on the information from the HDMI Lip-Sync-compatible TV.

When enabling the automatic correction function

Off

When not using the automatic correction function

Summary of Contents for ELITE VSX-LX505





















































































































































































































Search results

Summary of Contents for ELITE VSX-LX505

Reviews:

Related manuals for ELITE VSX-LX505

Brands by name

Popular brands

Pioneer ELITE VSX-LX505, Instruction Manual

Search results

Summary of Contents for ELITE VSX-LX505

Reviews:

Related manuals for ELITE VSX-LX505

Brands by name

Popular brands