background image

9

X:\print\Pioneer\19AJ\NAVI\19_Navi_AU_QRB3883(A5_Horizon)_INST\020Chapter.fm

AVIC-Z920DAB/AVIC-Z720DAB

19_Navi_AU_QRB3883(A5_Horizon)

En

En
g

lish

GPS aerial and its lead

In addition, you should lay or route each 
aerial lead as far as possible from other 
aerial leads. Do not bind, lay or route them 
together, or cross them. Electromagnetic 
noise will increase the potential for errors 
in the vehicle’s location display.

Consult with your nearest dealer if 
installation requires drilling holes or 
other modifications of the vehicle.

Before making a final installation of this 
product, temporarily connect the wiring 
to confirm that the connections are 
correct and the system works properly.

Do not install this product in a position 
where the opening of the LCD panel is 
obstructed by any obstacles, such as the 
gearstick. Before installing this product, be 
sure to leave sufficient space so that the 
LCD panel does not obstruct the gearstick 
when it is fully opened. This may cause 
interference with the gearstick, or a 
malfunction of the mechanism of this 
product.

Do not install this product in places 
subject to high temperatures or 
humidity, such as:
– Places close to a heater, vent or air 

conditioner.

– Places exposed to direct sunlight, such 

as on top of the dashboard.

– Places that may be exposed to rain, 

such as close to the door or on the 
vehicle’s floor.

Install this product in an area strong 
enough to bear its weight. Choose a 

position where this product can be firmly 
installed, and install it securely. If this 
product is not securely installed, the 
current location of the vehicle cannot be 
displayed correctly.

Install this product horizontally on a 
surface within 0 to 30 degrees tolerance 
(within 5 degrees to the left or right). 
Improper installation of the unit with the 
surface tilted more than these tolerances 
increases the potential for errors in the 
vehicle’s location display, and might 
otherwise cause reduced display 
performance.

When installing, to ensure proper heat 
dispersal when using this unit, make sure 
you leave ample space behind the rear 
panel and wrap any loose cables so they 
are not blocking the vents.

The cords must not cover the area shown 
in the figure below. This is necessary to 
allow the amps and navigation 
mechanism to dissipate heat.

Before installing

For AVIC-Z920DAB users

Installation notes

Leave ample 
space

5 cm

5 cm

 Do not cover this area.

The semiconductor laser will be damaged 
if it overheats, so don’t install this product 
anywhere hot- for instance, near a heater 
outlet.

1

Fastening this product to the factory 
radio-mounting bracket.

Position this product so that its screw 
holes are aligned with the screw holes 
of the bracket, and tighten the screws at 
three locations on each side.
Use either the truss head screws or flush 
surface screws, depending on the shape 
of the bracket’s screw holes.

 Factory radio-mounting bracket
 If the pawl interferes with 

installation, you may bend it down 
out of the way.

 Dashboard or console
 Truss head screw or flush surface 

screw
Be sure to use the screws supplied 
with this product.

 CAUTION

Do not cut the GPS aerial lead to shorten it 
or use an extension to make it longer. 
Altering the aerial cable could result in a 
short circuit or malfunction and 
permanent damage to this product.

The aerial should be installed on a level 
surface where radio waves will be 
blocked as little as possible. Radio waves 
cannot be received by the aerial if 
reception from the satellite is blocked.

Installation using the screw 
holes on the side of this 
product

Installing the GPS 
aerial

Installation notes

Summary of Contents for AVIC-Z720DAB

















Reviews: