3
X:\print\Pioneer\19AJ\NAVI\19_Navi_AU_QRB3883(A5_Horizon)_INST\020Chapter.fm
AVIC-Z920DAB/AVIC-Z720DAB
19_Navi_AU_QRB3883(A5_Horizon)
En
En
g
lish
•
Use this unit with a 12-volt battery and
negative earthing only. Failure to do so
may result in a fire or malfunction.
•
To avoid shorts in the electrical system,
be sure to disconnect the (–) battery
cable before installation.
WARNING
•
Use speakers over 50 W (maximum input
power) and between 4 Ω to 8 Ω
(impedance value). Do not use 1 Ω to 3 Ω
speakers for this product.
•
The black lead is earth. Please earth this
lead separately from the earth of high
current products such as power amps. Do
not earth more than one product
together with the earth from another
product. For example, you must
separately earth any amp unit away from
the earth of this product. Connecting
earths together can cause a fire and/or
damage the products if their earths
became detached.
•
When replacing the fuse, be sure to only
use a fuse of the rating prescribed on this
product.
•
When disconnecting a connector, pull the
connector itself. Do not pull the lead, as
you may pull it out of the connector.
•
This product cannot be installed in a
vehicle without ACC (accessory) position
on the ignition switch.
•
To avoid short-circuiting, cover the
disconnected lead with insulating tape. It
is especially important to insulate all
unused speaker leads, which if left
uncovered may cause a short circuit.
•
Attach the connectors of the same colour
to the corresponding coloured port, i.e.,
blue connector to the blue port, black to
black, etc.
•
For connecting a power amp or other
devices to this product, refer to the
manual for the product to be connected.
•
Since a unique BPTL circuit is employed,
do not directly earth the
side of the
speaker lead or connect the
side of
another side of the speaker lead together.
Be sure to connect the
side of the
speaker lead to the
side of the speaker
lead on this product.
•
The graphical symbol
placed on
the product means direct current.
•
When the ignition switch is turned on
(ACC ON), a control signal is output
through the blue/white lead. Connect to
an external power amp’s system remote
control terminal, the auto-aerial relay
control terminal, or the aerial booster
power control terminal (max. 300 mA 12
V DC). The control signal is output
Before installing this
product
To prevent damage
Notice for the blue/
white lead
ACC position
No ACC position
through the blue/white lead, even if the
audio source is switched off.
•
Be sure not to use this lead as the power
supply lead for the external power amps.
Such connection could cause excessive
current drain and malfunction.
•
Be sure not to use this lead as the power
supply lead for the auto-aerial or aerial
booster. Such connection could cause
excessive current drain and malfunction.
Important
When this product is in [Power OFF] mode,
the control signal is also turned off. If
[Power OFF] mode is cancelled, the control
signal is output again and the aerial is
extended with the auto aerial function (if
the aerial is being used). Be careful so that
the extended aerial does not come into
contact with any obstacles.
WARNING
•
To avoid the risk of accident and the
potential violation of applicable laws, this
product should never be used while the
vehicle is being driven except for
navigation purposes. And, also rear
displays should not be in a location
where it is a visible distraction to the
driver.
•
In some countries, the viewing of images
on a display inside a vehicle even by
persons other than the driver may be
illegal. Where such regulations apply they
must be obeyed and this product’s video
source should not be used.
GPS aerial 3.55 m
Microphone 3 m
Vehicle Bus conversion cable 13 cm
Refer to the instruction manual for the
Vehicle Bus adapter (sold separately).
Digital Radio aerial input
This product
Aerial jack
AV cable IN/OUT
Power supply
Fuse (10 A)
Wired remote input
Hard-wired remote control adapter can
be connected (sold separately).
CAUTION
For improved Digital Radio reception,
make sure a Digital Radio aerial with
phantom power input (active type) is used.
Pioneer recommends using AN-DAB1 (sold
separately). Current consumption of the
Digital Radio aerial should be 100 mA or
less.
WARNING
IMPROPER CONNECTION MAY RESULT IN
SERIOUS DAMAGE OR INJURY
INCLUDING ELECTRICAL SHOCK, AND
INTERFERENCE WITH THE OPERATION
Rear panel (main
terminals)
Power cord
