SX-LX70SW
55
5
6
7
8
5
6
7
8
C
D
F
A
B
E
5. Contents of failures
• The contents of fail
u
res are classified depending on the error displayed at PO
W
ER O
N
as follows:
S Y S
c k U
B a
E R R
p
• If "OC ERROR" doesn't occ
u
rs in the next operation when the power is t
u
rned on in the normal mode, it is s
u
spected that
the speaker terminal may be short-circ
u
ited.
1.
W
hen the c
u
stomer set
u
p, the vol
u
me was increased with the both poles of SP cable being short-circ
u
ited.
2.
W
hen the c
u
stomer set
u
p, the cond
u
ctor of SP cable was in contact with the chassis of main
u
nit.
• If "OC ERROR" occ
u
rs again, the following ca
u
ses may be s
u
spected:
1. Any (or some) of the fo
u
r digital amplifier ICs (TAS5142DKD) in the AMP ASSY may be broken.
2. Any portion between the above digital amplifier ICs and the speaker terminal may be short-circ
u
ited.
3. At any portion between the above digital amplifier ICs and the system component (PDC157A
8
), the line for SHUTDO
WN
may be short-circ
u
ited to the gro
u
nd or broken.
4. The voltage of
V
G+12 is low (less than 10
V
).
In any case, the following ca
u
ses are s
u
spected:
1.
The
comm
u
nication line to EEPROM (or Flash ROM) is broken or short-circ
u
ited.
2. The IC of EEPROM (or Flash ROM) itself has a defect.
• If "O
V
ERTEMP" doesn't occ
u
r in the next operation when the power is t
u
rned on in the normal mode, there is no abnormality.
(It may be a temporary over temperat
u
re. Lower the vol
u
me.)
• If "O
V
ERTEMP" occ
u
rs again, the following ca
u
ses may be s
u
spected:
1. Any (or some) of the fo
u
r digital amplifier ICs (TAS5142DKD) in the AMP ASSY may be broken.
2. At any portion between the above digital amplifier ICs and the system component (PDC157A
8
), the line for XOT
W
may be short-circ
u
ited to the gro
u
nd or broken.
3. The heat sink is not installed properly. (Screws are loosened, silicone grease is not applied, etc.)
Back
u
p error for PDC157A
8
,164A
8
(system
u
-com) control
Error due to backup failure
Error due to detection of overcurrent
D S P
c k U
B a
E R R
p
O
r r o
C
E
1
r
Over temperature error
O v
T e m
e r
p
O
r r o
C
E
2
r
Back
u
p error of PEG117 (DSP
u
-com) control
When an EEPROM failure of DSP occurs, "DSP BackUpERR" is displayed in 15 seconds after the power is turned on.
4. Contents of operation
• Basically, the operation of the service test mode is the same as that of the normal mode. In order to indicate that the
operation is in the test mode, the displays by f
u
nction are as shown below.
[Functions]
HDMI1
HDMI3
Digital1
Digital2
HDMI2
ipod
F.A
u
dioIn
FM/AM
Analog (RCA)
[FL display]
H D M I
1 S
V
R
E
i t a l
1 S
g
i
D
V
R
E
i t a l
2 S
g
i
D
V
R
E
l o g
S
a
n
A
V
R
E
i p o d
S
V
R
E
u d i o
I S
A
.
F
V
R
E
T u n e r
S
V
R
E
H D M I
2 S
V
R
E
H D M I
3 S
V
R
E
M
R a d i S
X
V
R
E
S I R I U S S
V
R
E
XM
SIRIUS
S A T
c k U
B a
E R R
p
Back
u
p error for PEG393(digital radio
u
-com) control
Summary of Contents for AS-LX70
