Pioneer Eclipse PE420GP Operation Manual Download Page 47

Emission Control Warranty Statement

Your Warranty Rights and Obligations

The California Air Resources Board and Amano Pioneer Eclipse
Corporation is pleased to explain the emissions control system’s warranty
on your 2012 small off-road engine.  In California, new equipment that
use small off-road engines must be designed, built, and equipped to meet
the State’s stringent anti-smog standards.  Amano Pioneer Eclipse
Corporation must warrant the emissions control system on your small 
off-road engine for the period listed below provided there has been no
abuse, neglect or improper maintenance of your equipment.  Your
emissions control system may include parts such as: carburetor’s or fuel
injection system, ignition system, catalytic converters, fuel tanks, valves,
filters, clamps, connectors, and other associated components.  Also,
included may be hoses, belts, connectors, sensors, and other 
emission-related assemblies.
Where a warrantable condition exists, Amano Pioneer Eclipse
Corporation will repair your small off-road engine at no cost to you
including diagnosis, parts and labor.

Manufacturer’s Warranty Coverage

This emissions control system is warranted for two years. If any
emissions-related part on your equipment is defective, the part will be
repaired or replaced by Amano Pioneer Eclipse Corporation.

Owner’s Warranty Responsibilities

(a)  As the small off-road engine owner, you are responsible for
performance of the required maintenance listed in your owner’s manual.
Amano Pioneer Eclipse Corporation recommends that you retain all
receipts covering maintenance on your small off-road engine, but Amano
Pioneer Eclipse Corporation cannot deny warranty solely for the lack of
receipts or your failure to ensure the performance of all scheduled
maintenance.
(b)  As the small off-road engine owner, you should however be aware
that Amano Pioneer Eclipse Corporation may deny you warranty
coverage if your small off-road engine or a part has failed due to abuse,
neglect, or improper maintenance or unapproved modifications.
(c)  You are responsible for presenting your small off-road engine to an
Amano Pioneer Eclipse Corporation distribution center or service center
as soon as the problem exists.  The warranty repairs should be
completed in a reasonable amount of time, not to exceed 30 days.  If you
have a question regarding your warranty coverage, you should contact
Amano Pioneer Eclipse Corporation at 1-800-367-3550.

Defects Warranty Requirements

(a)  The warranty period begins on the date the engine or equipment is
delivered to an ultimate purchaser.
(b)  General Emissions Warranty Coverage. Amano Pioneer Eclipse
Corporation as the manufacturer of each small off-road engine or
equipment must warrant to the ultimate purchaser and each subsequent
owner that the engine or equipment is:

(1)  Designed, built, and equipped so as to conform with all applicable   

regulations adopted by the Air Resources Board; and

(2)  Free from defects in materials and workmanship that causes the 

failure of a warranted part for a period of two years.

c)  The warranty on emissions-related parts will be interpreted as follows:

(1)  Any warranted part that is not scheduled for replacement as 

required maintenance in the written instructions required by    
subsection (d) must be warranted for the warranty period defined 
in Subsection (b)(2).  If any such part fails during the period of 
warranty coverage, it must be repaired or replaced by the 
manufacturer according to Subsection (4) below.  Any such part 
repaired or replaced under the warranty must be warranted for the 
remaining warranty period.

(2)  Any warranted part that is scheduled only for regular inspection in 

the written instructions required by subsection (d) must be 
warranted for the warranty period defined in Subsection (b)(2).  A

statement in such written instructions to the effect of “repair or 
replace as necessary” will not reduce the period of warranty           
coverage.  Any such part repaired or replaced under warranty 
must be warranted for the remaining warranty period.

(3)  Any warranted part that is scheduled for replacement as 

replacement as required maintenance in the written instructions 
required by subsection (d) must be warranted for the period of 
time prior to the first scheduled replacement point for that part.  If 
the part fails prior to the first scheduled replacement, the part must 
be repaired or replaced by the engine manufacturer according to 
Subsection (4) below.  Any such part repaired or replaced under 
warranty must be warranted for the remainder of the period prior 
to the first scheduled replacement point for the part.

(4)  Repair or replacement of any warranted part under the warranty 

must be performed at no charge to the owner at a warranty      
station.

(5)  Notwithstanding the provisions of Subsection (4) above, warranty 

services or Repairs must be provided at all manufacturer 
distribution centers that are franchised to service the subject 
engines.

(6)  The owner must not be charged for diagnostic labor that leads to 

the Determination that a warranted part is in fact defective, 
provided that such diagnostic work is performed at a warranty 
station.

(7)  The manufacturer is liable for damages to other engine            

components Proximately caused by a failure under warranty of any 
warranted part.

(8)  Throughout the emissions warranty period defined in Subsection 

(b)(2), the manufacturer must maintain a supply of warranted parts 
sufficient to meet the expected demand for such parts.

(9)  Any replacement part may be used in the performance of any 

warranty Maintenance or repairs and must be provided without 
charge to the owner.  Such use will not reduce the warranty     
obligations of the manufacturer.

(10) Add-on or modified parts that are not exempted by the Air 

Resources Board may not be used.  The use of any non-exempted 
add-on or modified parts will be grounds for disallowing a warranty 
claim.  The manufacturer will not be liable to warrant failures of 
warranted parts caused by the use of a non-exempted add-on or 
modified part.

(11) The manufacturer issuing the warranty shall provide any 

documents that describe that manufacturer’s warranty procedures 
or policies within five working days of request by the Air 
Resources Board.

(d) 

Emission Warranty Parts List

(1) Fuel Metering System

(i) Carburetor and internal parts and pressure regulator.
(ii) Cold start enrichment system.

(2) Air Induction System

(i) Intake manifold.
(ii) Air filter.

(3) Ignition System

(i) Spark Plugs.
(ii) Magneto or electronic ignition system.
(iii) Spark advance/retard system.

(4) Exhaust System

(iii) Exhaust manifold.

(5) Miscellaneous Items Used in Above Systems

(i) Electronic Fuel Cut-off control.
(ii) Vacuum, temperature, and time sensitive valves and switches.
(iii) Hoses, belts, connectors, and assemblies.

Amano Pioneer Eclipse Corporation will furnish with each new engine
written instructions for the maintenance and use of the engine by the
owner.

Exception:  This warranty does not apply to any machine models that do
not have a catalyst muffler.

Small Off-Road Engine Certification 

Warranty Form

41

Summary of Contents for PE420GP





















































Reviews: