PICOTE 2370000020 Operation & Safety Manual Download | Manualshive

Page: 6 / 19

background image

SAVE ALL WARNINGS AND INSTRUCTIONS FOR FUTURE REFERENCE

OPERATING INSTRUCTIONS

1. To close the Jaws, rotate the handle clockwise.

2. To open the Jaws, rotate the handle counter clockwise.

NOTE! The Small Grabber should only be used in an uncoiled position. Excessive use of
force may result in the tool breaking!

10

6

Picote Solutions Oy Ltd www.picoteinstitute.com

«
...
4
5
6
7
8
...
»

Summary of Contents for 2370000020




















Reviews:

No comments

Related manuals for 2370000020

Brand: Earlex Pages: 20

Brand: Paoli Pages: 68

Brand: Image Industries Pages: 32

Brand: Ryobi Pages: 8

Brand: Westfalia Pages: 20

Brand: Wacker Neuson Pages: 112

Brand: Cleco Pages: 38

Brand: HIKOKI Pages: 196

Brand: G-Tec Pages: 11

CP7600xB Series

Brand: CP Pages: 64

Brand: Parkside Pages: 96

Brand: FACHOWIEC Pages: 4

Brand: Max Pages: 14

Brand: NAL Pages: 2

Brand: Jarvis Pages: 12

Brand: Beta Pages: 18

Brand: Parkside Pages: 60

PRO RDP-CDLGP02

Brand: Raider Pages: 64

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands