pico Technology PicoSource PG900 Series User Manual Download Page 5 | Manualshive

Page: 5 / 56

background image

PicoSource PG900 Series User's Guide

1

Copyright © 2016 Pico Technology. All rights reserved.

pg900ug.en r1

1

Introduction

1.1

Overview

The PicoSource PG900 Series instruments are PC-based fast-edge pulse generators
that are fully compatible with USB 2.0 and 3.0 PCs.

The pulse generators are available in three differential output models and offer
extensive control over pulse parameters including amplitude, period, width and
deskew between output channels.

PicoSource PG911:

A two-channel pulse generator based on Step-Recovery Diode
(SRD) technology. It produces two pulses with opposite
polarity, up to 6 V amplitude with 60 ps rise time.

PicoSource PG912:
A two-channel pulse generator based on Tunnel Diode (TD)
technology. It is supplied with small remote tunnel diode
pulse heads that generate positive and negative 200 mV
pulses with 40 ps rise time.

PicoSource PG914:

A four-channel pulse generator based on both SRD and TD
technologies. It can produce two pulses with opposite polarity,
up to 6 V amplitude with 60 ps rise time, and two pulses with
opposite polarity, 200 mV amplitude and 40 ps rise time from
remote tunnel diode pulse heads.

PicoSource Pulse Generators are capable of producing pulses of either polarity with
very fast rise times. The generators will free-run or may be triggered from an external
source, with either positive or negative pulses, at rates of up to 1 MHz. The units are

designed to operate into 50 Ω lines.

The PicoSource instruments can be used as:

general-purpose pulse generators for the testing of semiconductors, components,
networks, electro-optical components etc.
fast rise/fall time step generators which can be used to check the dynamic
response of wide-band oscilloscopes and amplifiers
a stimulus for high-resolution TDR and TDT measurements
a step source for an ultra-wideband impulse forming network

For basic instructions on installing and using your pulse generator, please refer to

to use your pulse generator

or the Quick Start Guide supplied with your instrument.

Features

60 ps rise time at 6 V amplitude (integrated SRD pulse outputs)
40 ps rise time at 200 mV amplitude (tunnel diode pulse outputs)
1 Hz to 1 MHz repetition rate
200 ns to 4 µs pulse width
Continuous, external or manual trigger mode
Differential outputs with deskew
Low-jitter trigger input and output
Storage and carry case
USB 2.0- and 3.0- compatible

«
...
3
4
5
6
7
...
»

Summary of Contents for PicoSource PG900 Series

























































Reviews:

No comments

Related manuals for PicoSource PG900 Series

Brand: Cabela's Pages: 32

Brand: Feider Machines Pages: 26

Brand: Miller Pages: 56

Brand: National Instruments Pages: 37

Brand: DUROMAX Pages: 64

Brand: DUROMAX Pages: 64

Brand: DUROMAX Pages: 66

Brand: Schloder Pages: 20

Brand: iPower Pages: 2

Brand: Arconic Pages: 28

Brand: DEI Pages: 20

Brand: DEI Pages: 36

OTC Welbee WB-M350

Brand: Daihen Pages: 144

Brand: OfficeSource Pages: 2

Brand: YSONIC Pages: 28

Brand: Quipall Pages: 26

Brand: Briggs & Stratton Pages: 48

Brand: ABB Pages: 30

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands