pico Technology PicoSource PG900 Series User Manual Download Page 16 | Manualshive

Page: 16 / 56

background image

How to use your pulse generator

12

Copyright © 2016 Pico Technology. All rights reserved.

pg900ug.en r1

3

How to use your pulse generator

3.1

Connection diagrams

To set up your PicoSource pulse generator, follow the instructions below.

1.

Install the PicoSource PG900 software using the software disk supplied, or
download it from

picotech.com/downloads

2.

Plug the AC adaptor into the mains and connect the DC cable to the DC power
socket on the rear of your PicoSource pulse generator.

3.

Earth (ground) terminal.

Some laptop power supplies can produce electrical

noise which may interfere with your measurements. If this occurs, the earth
terminal can be connected to an external ground point (for example, on the
system you are testing) to provide a ground reference for the signal generator.
This can help to avoid external noise interfering with your signal integrity.
Alternatively, you can run the laptop using battery power.

4.

Connect your PicoSource pulse generator to the PC or hub using the USB cable
supplied.

5.

Once you have connected the pulse generator to the PC, run the PicoSource
PG900 software.

The following diagrams illustrate advanced setup options using a PicoSource pulse
generator, a PicoScope oscilloscope, and the device under test (DUT). In all setups,
the pulse generator shown can be substituted by the PicoSource PG914. Signal
connections should be made using precision SMA cables unless otherwise specified.
Trigger connections can be made using lower grade cables.

Diagram key

«
...
14
15
16
17
18
...
»

Summary of Contents for PicoSource PG900 Series

























































Reviews:

No comments

Related manuals for PicoSource PG900 Series

Brand: Ramsond Pages: 24

Brand: Briggs & Stratton Pages: 5

XP6500E XP SERIES

Brand: Generac Power Systems Pages: 40

Brand: Titan Pages: 23

Brand: Promate Pages: 48

39461 Generator

Brand: Chicago Electric Pages: 23

Brand: Kino Flo Pages: 16

Brand: PDWERTECH Pages: 18

Brand: Generac Portable Products Pages: 20

Brand: ANLU Pages: 9

Brand: Champion Global Power Equipment Pages: 4

Brand: M2TECH Pages: 10

Brand: Valex Pages: 12

Brand: Valex Pages: 24

KwikStart ProHD KS400

Brand: Associated Pages: 16

Power System 8335-GTC

Brand: IBM Pages: 46

Brand: Bandwidth10 Pages: 10

domnick hunter UHP10ZA-S

Brand: Parker Pages: 20

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands