background image

24

POWERLIGHT

!

 QUICK-CHANGE

#

ACCESSORIES

REFLECTORS:

PL3R ------

3”

 Shallow Background reflector rotates to control light for high key and back

lighting.

PL3RV-----

3”

 Veil 

Slotted

 Background reflector for veil and burst-lighting

PL5R-------

5”

 Deep Conical Background reflector.

PL7R-------

7 _”

 Standard high grain reflector.  35-degree coverage.

PL14R-----

14”

 Parabolic for portraits, feathering, flood and fill lighting.

  45-degree coverage.

PL16R-----

16”

 Parabolic for portraits, feathering, flood and fill lighting.

  60-degree coverage.

PL18R-----

18”

 Parabolic for soft illumination and flood lighting.

   125-degree coverage.

PL20R-----

20”

 Parabolic for portraits, feathering, flood and fill lighting.

65-degree coverage.

PL24R-----

24”

 Parabolic for soft illumination and flood lighting.

145-degree coverage.

Additional PowerLight Light-Shaping Accessory items and Kits.

Grids.

Snoots.

Soft Boxes.

Barndoor Sets.

Tilting Handle.

Scrim & Gel rings.
Eclipse Umbrellas.

Counter-Balance weights.

Contact your local dealer for these and other Professional Photographic products by:

Photogenic Professional Lighting

1268 Humbracht Circle, Bartlett, Illinois 60103-1631

www.Photogenicpro.com

Telephone: (630)830-2500   Fax: (630)830-2525

MANUAL PART NO.   016577-00V0-6-05

Summary of Contents for PLR1000DR

























Reviews: