background image

16

OPERATIONAL PARAMETERS

Solair

!

 Radio-Sync, Constant-Color PLR1000DR

Voltage Smart

#

 Radio-Sync, Constant Color PLRX1000DR

Flashing Rate:

The unit recharges quickly, as indicated by the READY light on the control panel.   A
quick series of flashes can be obtained within the limits of the recharge time.  Continuous
rapid flashing, however, can overheat and damage the flashtube and internal parts.  The
maximum recommended rate of flashing would depend upon the power level being used
and the amount of operation time.   Use the following chart to serve as a guide for the
maximum rate to use in your situation.

Power Level

Operating

Sec. Between

Number of

Time

Flashes

.

Flashes

Full

Continuous

17

Continuous

7 Minutes

10

40

2.5 Minutes

6

25

1/2

Continuous

8.3

Continuous

4 Minutes

4

60

1.4 Minutes

2

43

1/4

Continuous

4

Continuous

Exposure Information:

The following charts give the BCPS output for various umbrellas and reflectors.
Coverage angle is given in degrees.

Umbrella

32 inch

45 inch

60 inch

Coverage

120 degree

120 degree

120 degree

Full Power

11000

11166

11166

_

5500

5583

5583

_

2750

2792

2792

1/8

1375

1396

1396

1/16

688

698

698

1/32

344

349

349

1/64

172

174

174

1/128

86

87

87

Reflector

PL7R

PL14R

PL16R

PL18RWD

PL24R

Diameter

None

7 _”

14”

16”

18”

24”

Coverage

360

°

35

°

40

°

60

°

126

°

145

°

Full Power

4666

50000

35000

46666

7140

8400

_

2333

25000

17500

23333

3570

4200

_

1167

12500

8750

11667

1785

2100

1/8

583

6250

4375

5833

892

1050

1/16

292

3125

2188

2916

446

525

1/32

146

1562

1094

1458

223

262

1/64

73

781

547

729

112

131

1/128

37

391

274

364

56

66

GN@ASA100/10’

160

515

430

495

194

210

Summary of Contents for PLR1000DR

























Reviews: