Phoenix PCS300-x Installation Manual Download Page 8

OF

 12     PCS300 S

ERIES

 I

NSTALLATION

 G

UIDE

650-321-017

08/16

©2014 Phoenix Controls   

Specifications subject to change without notice.  Rev. C

2.4.3  Humidity and Temperature Offset and Display Adjustments: PCS300-x-DOS

When the unit is powered up, pressing 

SW1

 (Figure 9)will enter the user calibration adjustment mode. When pressed, the LCD will show the 

mode as page zero, P0.

The mode page numbers auto-scroll to P5 and then the unit returns to the normal run mode. Pressing 

SW1

 when the page number is displayed 

will show the calibration value that is associated with that mode. The variable will auto-scroll to show all allowed values for the selected page. 
Pressing 

SW1

 when the variable value you need is shown will record that value and return to showing page numbers.

Figure 8.    

SW1 calibration button

1

 When Active means moving the setpoint slider

Display toggles through selections

Even when the temperature setpoint is not displayed the terminations SET1 and SET2 are active, sending a 0 to 20 K

Ω

 signal out.

PCS300-x-DOS Adjustment Parameters

Parameter

Mode

Default

Adjustment

Temperature Offset

P0

0

±5° in 0.1° increments. A high accuracy reference is recommended.

Humidity Offset

P1

0

±5% in 0.1% increments or R34 when R34 is selected, humidity offset is set by 
turning potentiometer R34 situated just to the left of the OVR1 terminal. See 
Figure 12. A high accuracy reference is recommended.

Display Units

P2

F

°F or °C

Display RH to Temp Toggle Time

P3

5

3 to 11 seconds

Display Resoultion

P4

0

0 = 0.5
1 = 0.1

Display Section

P5

0

0 = Temperature, Humidity and Temperature Setpoint when active

1

 

1 = Temperature and Temperature Setpoint when active

1

2 = Humidity and Temperature Setpoint when active

1

3 = Temperature, Humidity and Temperature Setpoint

2

4 = Temperature and Temperature Setpoint

2

5 = Humidity and Temperature Setpoint

2

6 = Temperature Setpoint
7 = Temperature and Humidity

2, 3

8 = Temperature

3

 

9 = Humidity

3

Summary of Contents for PCS300-x













Reviews: