Phoenix PCS300-x Installation Manual Download Page 12

12 

OF

 12     PCS300 S

ERIES

 I

NSTALLATION

 G

UIDE

650-321-017

08/16

©2014 Phoenix Controls   

Specifications subject to change without notice.  Rev. C

2.10   Phoenix Controls Cables 

Cable

Type

Plenum

Rated

Function

Wire 

Gauge

Primary 

Vendor/Part #

Alternate Vendor/

Part #

Color Code

Notes

2C Round

No

24 Vac power  

18

Belden 9409

1: Red
2: Black

Must be stranded

24 Vac power

14

Belden 9411

2C Round

Yes

24 Vac power

18

Belden 82740

Windy City 
NP002360

1: Red
2: Black

Must be stranded

24 Vac power 

14

Windy City NP007960

TP

NO

FTT-10 (4,500 FT)
TP1250 (425 FT)

22

Windy City 107500
www,smartwire.com

1: White with Blue Stripe
2: Blue with White Stripe

FTT-10 (8,000 FT)

16

Windy City 109600
www,smartwire.com

TP

Yes

FTT-10 (4,500 FT)
TP1250 (425 FT)

22

Windy City 105500
S=SPOOL B=BOX

1: White with Blue Stripe
2: Blue with White Stripe

FTT-10 (8,000 FT)

16

Windy City 109500
www,smartwire.com

3C Round

No

Signal

22

Belden 8443

1: Red 
2: Black 
3: Green

Must be stranded

3C or 4C  
Round

Yes

Signal

22

Belden 88444

Windy City 004380

1: Red 
2: Black
3: Green
4: White (not used as 3C)

Must be stranded

4C Round

No

Signal

22

Belden 8444

Manhattan M13304

1: White 
2: Green
3: Black 
4: Red  

Must be stranded

5C Round

No

Signal

22

Belden 8445

Manhattan M13305

1: White
2: Brown 
3: Black 
4: Red  
5: Green

Must be stranded

8C 

No

Signal

22

Belden 9421

Manhattan M13308

1: White
2: Orange
3: Black
4: Red
5: Green
6: Yellow
7: Blue
8: Brown

No substitutes

8C 

Yes

Signal

22

Comtran 4956

1: White 
2: Orange
3: Black
4: Red
5: Green
6: Yellow
7: Blue
8: Brown 

No substitutes

3C 
MS/TP

No

Shielded

22

Belden 3106A 
(120 ohm)

1: White with Orange stripe
2: Orange with White stripe
3: Blue with White stripe   

Shielded with 
drain

3C 
MS/TP

Yes

Shielded

22

Connect-Air W223C-
2060YPC

1: Black
2: White
3: Red

Foil shield with 
drain wire

Phoenix and Phoenix Controls are trademarks of Honeywell International, Inc. 

The material in this document is for information purposes only and is subject to change without notice. Phoenix Controls assumes no responsibility for any errors 
or for consequential damages that may result from the use or misrepresentation of any of the material in this publication.

Phoenix Controls is a business of Honeywell International, Inc.

For additional information and a listing of our global offices, please visit our Web site at www.phoenixcontrols.com or call (800) 340-0007.

Summary of Contents for PCS300-x













Reviews: