Phoenix PCS300-x Installation Manual Download Page 11

©2014 Phoenix Controls   Specifications subject to change without notice. 

Rev. C

  650-321-017   08/16

PCS300 S

ERIES

 I

NSTALLATION

 G

UIDE

     11 

OF

 12

2.7  

Maintenance

Each controller requires minimal maintenance, but it is important to take note of the following:

If it is necessary to clean the outside of the front plate and/or the inside of the back plate, use a dry cloth.

Verify the tension of all wires and cables whenever the controller is serviced.

2.8  

Disposal

The Waste Electrical and Electronic Equipment (WEEE) Directive sets out regulations for the recycling and disposal of products. The WEEE2002/
96/EG Directive applies to standalone products, i.e., products that can function entirely on their own and are not a part of another system or piece 
of equipment. 

For this reason Phoenix Controls products are exempt from the WEEE Directive. Nevertheless, Phoenix Controls products are marked with the 
WEEE symbol, indicating that disposal of the devices shall not be done together with municipal waste.

 

Figure 9.   

WEEE Directive symbol

Products must be disposed of at the end of their useful life according to local regulations and the WEEE Directive.

2.9  

FCC Statement

CAUTION

Turn off power before any kind of servicing.

Note that there may be multiple power sources.

CAUTION

FCC: This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: 

1.  This device may not cause harmful interference. 

2.  This device must accept any interference received, including interference that may cause undesired operation.

Summary of Contents for PCS300-x













Reviews: