Philips Vari-lite VL3015LT User Manual Download Page 77

Page: 77 / 90

ROUBLESHOOTING

AND

AINTENANCE

02.9698.0002 0

13 December 2012

Troubleshooting Guide

If a problem is suspected, first try recalibrating the luminaire to prompt an error message. The chart
below provides possible causes and remedies for various error messages and/or symptoms.

Table A-2: Troubleshooting Chart

Message

Symptom

Description

Possible Cause/Remedy

Lamp
Power
Douse

Lamp does not strike
upon start-up

Lamp Off option is config-
ured

- Reconfigure lamp startup option in Lamp config

menu.

n/a

Lamp douses frequently

Lamp Douse

Fan failure...

- check fans for proper connection and operation.

n/a

Lamp will not strike

Lamp Strike Failure

Lamp cutout switch engaged...

- check lamp cutout switches at lamp box and fan

ducts.

Bad lamp...

- replace lamp.

Low input voltage...

- check input power (must be 200 to 264 VAC).

n/a

Luminaire behaves
oddly

Profile Not Matched

Profile not set correctly...

- confirm console patch matches fixture DMX

address.

- confirm DMX protocol matches console profile.

n/a

Luminaire does not
power up

No power

Switch not turned on...

- verify switch is turned on.

Not plugged in...

- ensure A/C cable is connected to power source.

n/a

Self tests will not run or
software download does
not work.

DMX Data Input

Detecting DMX data...

- disconnect DMX input cable.

n/a

No response to DMX
data

DMX Failure

MCB connector disconnected...

- check MCB DATA IN connection.

n/a

Erratic control of
luminaire

DMX Termination

No DMX termination or termination not correct...

- check for DMX terminator.

n/a

No control of pan or tilt
movement from DMX
(console) commands

Pan/Tilt do not respond to
DMX

Pan/Tilt do not respond to DMX...

- Turn off Followspot Mode in Setup menu.

(Ensure

that Followspot handle accessories are not
installed!)

- Pan/Tilt transport locks need to be disengaged.

Summary of Contents for Vari-lite VL3015LT


























































































Search results

Summary of Contents for Vari-lite VL3015LT

Reviews:

Related manuals for Vari-lite VL3015LT

Brands by name

Popular brands

Philips Vari-lite VL3015LT, User Manual

Search results

Summary of Contents for Vari-lite VL3015LT

Reviews:

Related manuals for Vari-lite VL3015LT

Brands by name

Popular brands