manualshive.com logo in svg

Philips SC16C2550, Manual

The Philips SC16C2550 user manual is a comprehensive guide that provides detailed instructions for operating this reliable device. Explore its functionalities and optimize your user experience with this free manual download from manualshive.com. Discover all the features and capabilities of the Philips SC16C2550 for enhanced performance and convenience.

Share
Download
background image

Philips Semiconductors

SC16C2550

Dual UART with 16 bytes of transmit and receive FIFOs and IrDA

encoder/decoder

Product data

Rev. 03 — 19 June 2003

7 of 46

9397 750 11621

© Koninklijke Philips Electronics N.V. 2003. All rights reserved.

INTA,
INTB

30, 29 33, 32

30, 29

O

Interrupt A, B (3-State). This function is associated with individual channel
interrupts, INTA, INTB. INTA, INTB are enabled when MCR bit 3 is set to a
logic 1, interrupts are enabled in the interrupt enable register (IER), and is
active when an interrupt condition exists. Interrupt conditions include:
receiver errors, available receiver buffer data, transmit buffer empty, or
when a modem status flag is detected.

IOR

21

24

19

I

Read strobe (Active-LOW strobe). A logic 0 transition on this pin will load
the contents of an internal register defined by address bits A0-A2 onto the
SC16C2550 data bus (D0-D7) for access by external CPU.

IOW

18

20

15

I

Write strobe (Active-LOW strobe). A logic 0 transition on this pin will
transfer the contents of the data bus (D0-D7) from the external CPU to an
internal register that is defined by address bits A0-A2.

OP2A,
OP2B

31, 13 35, 15

32, 9

O

Output 2 (user-defined). This function is associated with individual
channels, A through B. The state at these pin(s) are defined by the user
and through MCR register bit 3. INTA, INTB are set to the active mode and
OP2 to logic 0 when MCR[3] is set to a logic 1. INTA, INTB are set to the
3-State mode and OP2 to a logic 1 when MCR[3] is set to a logic 0. See
bit 3, Modem Control Register (MCR[3]). Since these bits control both the
INTA, INTB operation and OP2 outputs, only one function should be used
at one time, INT or OP2.

RESET

35

39

36

I

Reset (Active-HIGH). A logic 1 on this pin will reset the internal registers
and all the outputs. The UART transmitter output and the receiver input will
be disabled during reset time. (See

Section 7.11 “SC16C2550 external

reset condition”

 for initialization details.)

RXRDYA,
RXRDYB

-

34, 23

31, 18

O

Receive Ready A, B (Active-LOW). This function is associated with
PLCC44 and LQFP48 packages only. This function provides the
RX FIFO/RHR status for individual receive channels (A-B). RXRDYn is
primarily intended for monitoring DMA mode 1 transfers for the receive data
FIFOs. A logic 0 indicates there is a receive data to read/upload, i.e.,
receive ready status with one or more RX characters available in the
FIFO/RHR. This pin is a logic 1 when the FIFO/RHR is empty or when the
programmed trigger level has not been reached. This signal can also be
used for single mode transfers (DMA mode 0).

TXRDYA,
TXRDYB

-

1, 12

43, 6

O

Transmit Ready A, B (Active-LOW). This function is associated with
PLCC44 and LQFP48 packages only. These outputs provide the
TX FIFO/THR status for individual transmit channels (A-B). TXRDYn is
primarily intended for monitoring DMA mode 1 transfers for the transmit
data FIFOs. An individual channel’s TXRDYA, TXRDYB buffer ready status
is indicated by logic 0, i.e., at lease one location is empty and available in
the FIFO or THR. This pin goes to a logic 1 (DMA mode 1) when there are
no more empty locations in the FIFO or THR. This signal can also be used
for single mode transfers (DMA mode 0).

V

CC

40

44

42

I

Power supply input.

XTAL1

16

18

13

I

Crystal or external clock input. Functions as a crystal input or as an
external clock input. A crystal can be connected between this pin and
XTAL2 to form an internal oscillator circuit. This configuration requires an
external 1 M

Ω

 resistor between the XTAL1 and XTAL2 pins. Alternatively,

an external clock can be connected to this pin to provide custom data rates.
(See

Section 6.8 “Programmable baud rate generator”

.) See

Figure 5

.

Table 2:

Pin description

…continued

Symbol

Pin

Type Description

DIP40 PLCC44 LQFP48

Summary of Contents for SC16C2550















































Reviews:

No comments

Related manuals for SC16C2550

Yaesu FT-227R Memorizer Instruction Manual preview
FT-227R Memorizer
Brand: Yaesu Pages: 42
Icom IC-U400 Owner'S Manual preview
IC-U400
Brand: Icom Pages: 16
Bernafon Fusion2 mini RITE Installation Manual preview
Fusion2 mini RITE
Brand: Bernafon Pages: 2
Linear Multi-code 4140 Installation Instructions preview
Multi-code 4140
Brand: Linear Pages: 2
R.V.R. Electronica PTRLNV/4 User Manual preview
PTRLNV/4
Brand: R.V.R. Electronica Pages: 40
S+S Regeltechnik 1301-1214-0010-200 Operating Instructions, Mounting & Installation preview
1301-1214-0010-200
Brand: S+S Regeltechnik Pages: 32
Sytech SY-1528 User Manual preview
SY-1528
Brand: Sytech Pages: 6
PCB Piezotronics IMI Sensors 682C33 Installation And Operating Manual preview
IMI Sensors 682C33
Brand: PCB Piezotronics Pages: 22
Gatekeeper Systems Long Range Transmitter 2 User Manual preview
Long Range Transmitter 2
Brand: Gatekeeper Systems Pages: 5
Evikon PluraSens E2648-NH3-E User Manual preview
PluraSens E2648-NH3-E
Brand: Evikon Pages: 21
S+S Regeltechnik PREMASGARD SHD652 Operating Instructions, Mounting & Installation preview
PREMASGARD SHD652
Brand: S+S Regeltechnik Pages: 16
INOR IPAQ-L User Instructions preview
IPAQ-L
Brand: INOR Pages: 2
Rotronic CF5-D Installation Manual preview
CF5-D
Brand: Rotronic Pages: 4
BK Medical Type 2052 User Manual preview
Type 2052
Brand: BK Medical Pages: 28
ABACOM Technologies TX-FM Quick Start Manual preview
TX-FM
Brand: ABACOM Technologies Pages: 4
S+S Regeltechnik THERMSGARD RGTM2 Series Operating Instructions, Mounting & Installation preview
THERMSGARD RGTM2 Series
Brand: S+S Regeltechnik Pages: 16
Adamczewski AD-LU 60 FE Operating Manual preview
AD-LU 60 FE
Brand: Adamczewski Pages: 31
BRONDI FX-300 TWIN PMR 446 Instruction Manual preview
FX-300 TWIN PMR 446
Brand: BRONDI Pages: 20

Brands by name

Popular brands

Load more brands