Philips NetCam DVR Installation Instructions Manual Download Page 12 | Manualshive

Page: 12 / 35

background image

2.2

Installing NetCam DVR Setup Program

2.2.1

Installing for the first time

Copy the ‘NetCam DVR
Viewer’ program files onto
your PC. Click ‘setup.exe’
file. Follow the instructions.

It is recommended that you
reboot your PC after the
setup procedure is completed.

When prompted for “Locked
file” for MSFLXGRD.ocx,
MSCOMCT2.ocx and
COMCTL32.ocx select “Reboot”.

2.2.2

Modifying, Repairing & Removing

If you have already installed the NetCam DVR Viewer and select ‘setup.exe’, a
window is displayed showing the options ‘Modify’, ‘Repair’, and ‘Remove’.

The three options are to fix the already installed NetCam DVR Viewer as well as
to upgrade to a newer version. If you have a problem with the NetCam DVR
Viewer, you may modify manually, repair automatically, or remove and reinstall
again. However, it is recommended that you remove and reinstall the NetCam
DVR Viewer, if your software
does not work properly.

Modifying

Modify the existing NetCam
DVR Viewer manually by
selecting the file that you
want to modify.

■

Select ‘Modify’ mode.

12

NetCam DVR

Section 2

DVR_NC_ii_98911_0047.qxd 12/13/00 1:53 PM Page 12

«
...
10
11
12
13
14
...
»

Summary of Contents for NetCam DVR




































Reviews:

No comments

Related manuals for NetCam DVR

Brand: Zivif Pages: 14

Interlogix 60-875 Simon

Brand: GE Pages: 40

Brand: GE Security Pages: 2

Brand: Panasonic Pages: 48

BL-C1A - Network Camera

Brand: Panasonic Pages: 4

Brand: Panasonic Pages: 8

Brand: S/C Black Pages: 34

Brand: Digisol Pages: 25

Brand: FAAST Pages: 12

Brand: Vicon Pages: 28

Brand: DSE Pages: 20

Brand: Zavio Pages: 16

Brand: Hanwha Vision Pages: 65

Brand: EverFocus Pages: 19

Brand: Smart Witness Pages: 6

Brand: Datakom Pages: 13

Brand: dallmeier Pages: 104

Brand: nedis Pages: 40

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands