manualshive.com logo in svg

Philips LPC2119, User Manual

The Philips LPC2119 User Manual is an essential resource for optimizing your experience with this advanced product. Easily downloadable for free at manualshive.com, this comprehensive manual provides step-by-step instructions, ensuring seamless setup and operation. Unlock the full potential of your Philips LPC2119 with our user-friendly manual.

Share
Download
background image

UART1

124

January 08, 2004

Philips Semiconductors

Preliminary User Manual

LPC2119/2129/2292/2294

ARM-based Microcontroller

UART1 Receiver Buffer Register (U1RBR - 0xE0010000 when DLAB = 0, Read Only)

The U1RBR is the top byte of the UART1 Rx FIFO. The top byte of the Rx FIFO contains the oldest character received and can 
be read via the bus interface. The LSB (bit 0) represents the “oldest” received data bit. If the character received is less than 8 
bits, the unused MSBs are padded with zeroes.

The Divisor Latch Access Bit (DLAB) in U1LCR must be zero in order to access the U1RBR. The U1RBR is always Read Only.

UART1 Transmitter Holding Register (U1THR - 0xE0010000 when DLAB = 0, Write Only)

The U1THR is the top byte of the UART1 Tx FIFO. The top byte is the newest character in the Tx FIFO and can be written via 
the bus interface. The LSB represents the first bit to transmit.

The Divisor Latch Access Bit (DLAB) in U1LCR must be zero in order to access the U1THR. The U1THR is always Write Only.

UART1 Divisor Latch LSB Register (U1DLL - 0xE0010000 when DLAB = 1)

UART1 Divisor Latch MSB Register (U1DLM - 0xE0010004 when DLAB = 1)

The UART1 Divisor Latch is part of the UART1 Baud Rate Generator and holds the value used to divide the VPB clock (pclk) in 
order to produce the baud rate clock, which must be 16x the desired baud rate. The U1DLL and U1DLM registers together form 
a 16 bit divisor where U1DLL contains the lower 8 bits of the divisor and U1DLM contains the higher 8 bits of the divisor. A ‘h0000 
value is treated like a ‘h0001 value as division by zero is not allowed.The Divisor Latch Access Bit (DLAB) in U1LCR must be 
one in order to access the UART1 Divisor Latches.

Table 88: UART1 Receiver Buffer Register (U1RBR - 0xE0010000 when DLAB = 0, Read Only)

U1RBR

Function

Description

Reset 

Value

7:0

Receiver Buffer 

Register

The UART1 Receiver Buffer Register contains the oldest received byte in the UART1 Rx 
FIFO.

un-

defined

Table 89: UART1 Transmit Holding Register (U1THR - 0xE0010000 when DLAB = 0, Write Only)

U1THR

Function

Description

Reset 

Value

7:0

Transmit 

Holding Register

Writing to the UART1 Transmit Holding Register causes the data to be stored in the 
UART1 transmit FIFO. The byte will be sent when it reaches the bottom of the FIFO and 
the transmitter is available.

N/A

Table 90: UART1 Divisor Latch LSB Register (U1DLL - 0xE0010000 when DLAB = 1)

U1DLL

Function

Description

Reset 

Value

7:0

Divisor Latch 

LSB Register

The UART1 Divisor Latch LSB Register, along with the U1DLM register, determines the 
baud rate of the UART1.

0x01

Summary of Contents for LPC2119














































































































































































































































































Reviews:

No comments

Related manuals for LPC2119

ZEHUS Controller Rider'S Manual preview
Controller
Brand: ZEHUS Pages: 28
TCS Basys Controls QD Series Troubleshooting Worksheet preview
QD Series
Brand: TCS Basys Controls Pages: 2
Datapath HX4 Quick Start Manual preview
HX4
Brand: Datapath Pages: 12
Saftronics CV10 Quick Start Manual preview
CV10
Brand: Saftronics Pages: 13
SAI HVAC Compact Comfort VAV12 User Manual preview
Compact Comfort VAV12
Brand: SAI HVAC Pages: 16
Sailor N420 Technical Manual preview
N420
Brand: Sailor Pages: 1
Ultraflex B47 Installation Instructions Manual preview
B47
Brand: Ultraflex Pages: 7
Linear Technology LTC3703 Manual preview
LTC3703
Brand: Linear Technology Pages: 32
Nice One-Max Installation And Use Instructions And Warnings preview
One-Max
Brand: Nice Pages: 32
LAB-EL LB-762 Installation Manual preview
LB-762
Brand: LAB-EL Pages: 25
ProMinent DCM 5 Series Quick Start Manual preview
DCM 5 Series
Brand: ProMinent Pages: 2
Italtecnica Brio 2000 Owner'S Manual preview
Brio 2000
Brand: Italtecnica Pages: 16
YASKAWA T1000V Technical Manual preview
T1000V
Brand: YASKAWA Pages: 444
Gira 0425 00 Quick Start Manual preview
0425 00
Brand: Gira Pages: 7
Inverter sMove s4 AP Instructions preview
sMove s4 AP
Brand: Inverter Pages: 2
Tripp Lite NetController B042-004 Specifications preview
NetController B042-004
Brand: Tripp Lite Pages: 2
G-Systems GSE AC-EC User Manual preview
GSE AC-EC
Brand: G-Systems Pages: 66
Madas FRG/2MBC Manual preview
FRG/2MBC
Brand: Madas Pages: 52

Brands by name

Popular brands

Load more brands