manualshive.com logo in svg

Philips LIGHTOLIER CONTROLS LYTESCENE ILSCLTSII, User Manual

Share
Download
Philips LIGHTOLIER CONTROLS LYTESCENE ILSCLTSII User Manual Download Page 29

 L

YTE

S

CENE

 II T

OUCH

 S

CREEN

 U

SER

’

S

 G

UIDE

R

EAL

 T

IME

 C

LOCK

 F

EATURE

2 7

Add a New Event

Events can be added to correspond with daily routines or other occasions, based on specific 
astronomical clock timing. Options such as holiday exceptions and Automatic Shutoff (for Off events) 
can be specified using additional windows. Automatic Shutoff settings are specified so that if a Local 
Master or Remote selects a Preset other than Off during the checking period, a new one-time event is 
added which schedules an Off event in the Shutoff period specified (maximum 4 hours).

To add a new event:

Step 1. At Real Time Clock screen, press 

New Event 

tab.

Step 2. At Modify Event window, configure event as required. Use Preset and ID drop-

down menus to specify which ILS Master/Remote Scene will be triggered.

Step 3. If this is a one-time event, check box to specify. (One-time events will be 

removed from list after it occurs.)

Step 4. If exceptions for holidays or other special events are required, press 

Exceptions

.

Step 5. At Exceptions windows, configure exclusions. Press 

Close

.

Summary of Contents for LIGHTOLIER CONTROLS LYTESCENE ILSCLTSII





































Reviews:

No comments

Brands by name

Popular brands

Load more brands