manualshive.com logo in svg

Philips LIGHTOLIER CONTROLS LYTESCENE ILSCLTSII, User Manual

Share
Download
Philips LIGHTOLIER CONTROLS LYTESCENE ILSCLTSII User Manual Download Page 23

 L

YTE

S

CENE

 II T

OUCH

 S

CREEN

 U

SER

’

S

 G

UIDE

C

ONFIGURING

 

A

 M

ASTER

2 1

Configuring Alarm Actions

If wired to an alarm system, a Master can be programmed to react in different ways to an alarm trigger.

To configure alarm settings:

Step 1. At ILS Master window, press 

Configure Master

 tab.

Step 2. At Setup window, press 

Options

 tab.

Step 3. At Alarm section, use buttons to configure how Master will react to an alarm 

trigger.

Step 4. Press 

OK

.

Configuring Master Mode

A 16-position terminal strip is located on the back of each Master Station, which is used to hardwire 
alarms and other remote lock devices into the system. This strip is divided into eight inputs with 
common and six LED outputs with drive. The function of these inputs and outputs can be changed by 
configuring the Master Mode. Functions include:
•

Cinema Cycle

 - A remote closure causes the unit to cycle through Scenes A, B, C and D. This 

closure comes from a projector and can automatically control the lights in a movie theater. The ON 
scene is reserved for ‘clean up/emergency.’

•

Alarm

 - A remote closure comes from an alarm system and causes all the channels to either go to 

Full On or cycle between Full On and Off.

Once the terminal strip is wired according to the desired network configuration, the Terminal Strip 
Mode must be set for proper operation. This can be configured from the LyteScene II Touch Screen.

Press to launch Setup window

Specify alarm
response actions

Summary of Contents for LIGHTOLIER CONTROLS LYTESCENE ILSCLTSII





































Reviews:

No comments

Brands by name

Popular brands

Load more brands