background image

eW Burst Powercore    Product Guide

18

Installation

eW Burst Powercore LED fixtures offer a wash of high-intensity warm or neutral 

white light for spotlighting, site, and accent lighting. Powercore delivers line voltage 

directly to the fixture and eases installation by eliminating the need for external 

power supplies or special wiring. 

Owner / User Responsibilities 

It is the responsibility of the contractor, installer, purchaser, owner, and user to 

install, maintain, and operate eW Burst Powercore fixtures in such a manner as to 

comply with all applicable codes, state and local laws, ordinances, and regulations. 

Consult with the appropriate electrical inspector to ensure compliance.

Installing in Damp or Wet Locations

When installing in damp or wet locations, it is good practice to seal all fixtures and 

junction boxes with electronics-grade RTV silicone sealant to ensure that moisture 

cannot enter or accumulate in any wiring compartments, cables, or other electrical 

parts. You must use suitable outdoor-rated junction boxes when installing in wet or 

damp locations. Additionally, you must use gaskets, clamps, and other parts required 

for installation to comply with all applicable local and national codes

Prepare for the Installation

1.  Carefully inspect the box containing eW Burst Powercore and the contents for 

any damage that may have occurred in transit.

2.  Ensure that all additional parts and tools are available, including:

eW Burst Powercore Architectural Installations

•  The provided stainless steel screws for outdoor installations
•  The provided junction box gasket for outdoor installations
•  Unless surface-mounting, one 4 in (102 mm) round US electrical junction box 

per fixture, rated for your application, with 3.5 in (89 mm) center-to-center 

screw holes for attaching the fixture’s base. (Refer to the manufacturer’s 

literature for additional items required for mounting or sealing.)

•  A 5/16 in or 8 mm hex wrench for fixture tilting and locking
•  A 1/8 in or 3 mm hex wrench for fixture swiveling and locking

eW Burst Powercore Landscape Installations

•  The provided locking nut
•  One electrical junction box or mounting accessory per fixture, rated for your 

application. (Refer to the junction box or accessory manufacturer’s literature 

for specific information on mounting or sealing.)

•  A 6 mm hex wrench for fixture tilting and locking
•  A 33 mm wrench for locking the fixture in place

All Installations

 •  A sufficient length 3-conductor wire. We recommend 12 AWG (2.05 mm) 

stranded copper wire.

•  Conduit as required
•  Electronics-grade room temperature vulcanizing (RTV) silicone sealant as 

required

•  A 5/32 in hex wrench for installing accessories

E

 Refer to the eW Burst Powercore 

Installation Instructions for specific warning 

and caution statements.

Included in the box

eW Burst Powercore Architectural

eW Burst Powercore Architectural fixture
(4) 10-24 stainless steel screws for outdoor installation
Junction box gasket
Installation Instructions

eW Burst Powercore Landscape

eW Burst Powercore Landscape fixture
Locking nut
Installation Instructions

Summary of Contents for eW Burst Powercore





























Reviews: