Notes
8
DBC1220GL Installation Manual Rev I.docx
Check the following list. If you are still unable to rectify the situation, contact your nearest Dynalite office. A complete list
of distributors worldwide can be found on the Internet at:
Please ensure that you have completed the following prior to calling our technical support department.
Check all symptoms in the Troubleshooting list
Check for any deviations between the installation and the installation instructions
Make a list of the model numbers of all devices used in the system
SYMPTOM
PROBABLE CAUSE
ACTION
Dimmer does not operate at all. No Service LED
activity. Power supply indicator LED on PCB not
lit.
Incorrect connection of mains supply or no
power available.
Check power supply to dimmer. Check Line
and Neutral input connections.
Power supply indicator LED lit, but no Service
LED activity.
Supply voltage too low, short circuit on
network.
Control PCB faulty.
Check supply voltage is at least 75% of rated
voltage. Check 5V & 12V terminal voltages,
5V supply must be present. Disconnect
network bus and restore power. Replace
control PCB.
Dimmer will not respond to control panel push
buttons.
Control
panel
incorrectly
wired.
Incorrect configuration.
Check operation of LEDs on control panel.
Push button on panel and study response of
service LED.
Dimmer operates properly but circuit breakers
keep tripping.
Instant tripping: - short circuit on load.
Delayed tripping: - Dimmer overloaded.
Check load wiring for short circuits.
Verify dimmer loading with current tester
(don’t forget to de-rate for low power-factor
loads and transformer losses). Check that the
breaker terminals are tight.
Fluorescent lights won’t dim.
Wrong type of ballast or ballast incorrectly
wired. Control cable from dimmer to ballasts
not installed.
Check ballast type. Check actual wiring
against ballast manufacturer’s diagram.
Check 1-10V/DSI/DALI cable and settings.
specification
Supply:
230V ±14% 50/60Hz 3-Phase Y at 63A per phase
Line Outputs:
12 x Switched outputs at 20A per channel (total device load 189A)
Control Outputs:
12 x load control outputs, selectable to 1-10V, DSI or DALI
Protection:
12 x 20A 6kA single pole thermal magnetic circuit breakers
Switching Device:
Relay – 50A 230V AC inductive (5000W lighting load rated)
Control Inputs:
1 x RS485 DyNet serial port
1 x programmable dry contact AUX input
User Controls:
Service switch
Diagnostic LED
DyNet DC VE:
120mA (Capacity for approx 6 panels)
Preset Scenes:
170
Supply Terminals:
Line1, Line2, Line3
1 x 35mm
2
max conductor size
Output Terminals:
Line for each channel
1 x 6mm
2
max conductor size
Neutral link bar provided
Earth link bar provided
0V/DSI/DALI, +V/DSI/DALI for each channel
1 x 2.5mm
2
max conductor size
Cable Entries:
Mains – 4 x 25mm dia. knockouts mounted on a 85mm x 85mm removable gland plate
Loads – 6 x 25mm dia. knockouts located on the right hand side of the unit
Data – 1 x 25mm dia. knockout
Diagnostic Functions:
Device online/offline status
Circuit breaker trip monitoring (optional)
Circuit run time tracking (optional)
Compliance:
CE, C-Tick
Operating Environment:
Ambient temperature 40
C max. RH 90% max non condensing
Construction:
Alloy/Steel wall mount case with epoxy finish
Dimensions:
H 457mm x W 252mm x D 126mm
Dimensions –RCBO version:
H 585mm x W 252mm x D 126mm
Weight:
10.25 Kilograms
DBC1220GL Installation Manual Rev I.doc Specifications and design subject to change without notice.
Dynalite Manufactured by WMGD Pty Ltd (ABN 33 097 246 921). All rights reserved. Dynalite, Dimtek, DyNet and DLight and associated logos are the
registered trademarks of Dynalite Intelligent Light Pty Ltd. Not to be reproduced without permission.
Unit 6, 691 Gardeners Road Mascot NSW 2020 Australia Tel: +61 2 8338 9899 Fax: +61 2 8338 9333
E-mail:
