10
Directions for use
73
MG2.1E
21
To select connected equipment
If the TV is connected to a video recorder with the EasyLink function, in some cases
the TV will be switched on, even when the TV was in standby. (E.g. playback tape,...)
This is not possible when Child Lock On is selected.
Equipment connected with an aerial cable only :
•
Select the programme number under which you have stored the test signal
with the digit keys.
Equipment connected to a euroconnector or to the right side of
the TV
•
Press the
w
key repeatedly to select
EXT1
,
EXT2
or
FRONT
, according to
where you connected your equipment at the back or the right side of your TV.
Remark : Most equipment (decoder, video recorder, satellite receiver) carries out the
switching itself.
Do you want to watch TV channels again ?
•
Enter the programme number of the TV channel which you want to watch with
the digit keys or press the
w
key repeatedly to select
TV
.
Most of the audio and video equipment from our range of products can be
operated with the remote control of your TV.
Video recorder, DVD and satellite keys
Video recorder
Keep the
VCR
key on the left side of the remote control pressed and
simultaneously press:
®
for record,
Ò
for rewind,
‡
for stop,
π
for play,
†
for fast forward,
◊
for selecting 1- or 2-digit programme numbers from the video
recorder or DVD tuner,
- P +
for fast programme selection from the video recorder tuner,
0
to
9
to select a programme number from your video recorder tuner,
B
to switch the video recorder to standby
These keys function with equipment which use the RC5 signalling standard.
If your video recorder has the EasyLink function, the key
INSTANT
®
for record and
stop can be operated in the TV mode.
If your EasyLink videorecorder has the system standby function and when you press
the
B
key for 3 seconds, both TV and the video recorder are switched to standby.
B
®
Ò
‡
π †
f
h
U
æ
w
b
OK
V
P
SMART
DNR
INSTANT
M
a
Q
®
q
b
S
X
2
1
3
5
4
6
8
7
9
0
B
®
Ò
‡
π †
¬
i
0
f
h
U
æ
w
b
OK
◊
B
®
Ò
‡
π
†
®
20
Camera and camcorder
•
Connect your camera or camcorder at the right side of your TV.
•
Connect the equipment to
VIDEO
2
and
AUDIO L
3
for mono equipment.
•
Press the
X
key repeatedly to select the sound coming from one or both
loudspeakers of your TV.
•
For stereo equipment also connect
AUDIO R
3
.
S-VHS quality with a S-VHS camcorder is obtained by connecting the S-VHS
cables with the
S-VIDEO
input
1
and
AUDIO
inputs
3
.
Other equipments
Connect the eurocable
1
to
EXTERNAL 1
as shown opposite.
Only for Digital Sources :
•
Press
U
and
h
at the same time.
•
Select
Present
in the Setup menu of the
INSTALLATION
menu.
This offers you optimum picture quality for your digital equipment, like a DVD,
a digital satellite tuner or a similar digital device.
•
Press the red
®
key to switch off all menus.
Audio equipment / Amplifier
•
Connect the audio cables to the audio input of your audio equipment and to
AUDIO L
and
R
at the back of your TV.
You can listen to your TV sound via your audio equipment.
Headphone
•
Insert the plug into the headphone socket
L
at the right side of the TV.
•
Press
¬
on the remote control to switch off the internal loudspeakers of the
TV.
The headphone impedance must be between 8 and 4000 Ohm. The headphone
socket has a 3.5 mm jack.
In the
SOUND
menu select
Headphone
to adjust the headphone volume and
to select dubbed or original language (when the TV channel broadcasts in two
languages) for your headphone sound. See p. 10.
If you want to connect more equipment to your TV, consult your dealer.
1
EXTERNAL
DVD
1
AUDIO
INSTALLATION
Menu language
Country
Automatic Installation
Manual Installation
Give Name
Reshuffle
Favourite Programmes
SETUP
J
SETUP
SETUP
DVD
Decoder/Descrambler
(Picture tilt)
Information Line
Factory settings
Auto format
Yes/No
INSTALLATION
J
Digital Sources
AUDIO
VIDEO
S•VIDEO
3
2
1
L