Philips 3000 series Service Manual Download Page 52

Page: 52 / 79

PHILIPS 4000 and 3000 05 SERVICE MODE

11/18

The user can switch the level by pressing the Button Stand-By, the machine shows the level of the

test:

a) Level 1 : Led Espresso ON (G), Led Stand-by ON (R)

b) Level 2 : Led Espresso ON (G), Led Descale ON (O)

c) Level 3 : Led Espresso ON (G), Led Descale ON (O), Led Calc-Clean ON (O)

d) Level 4 : Led Espresso ON (G), Led Descale ON (O), Led Calc-Clean ON (O),Led Rinsing ON (O)

e) Level 5 : Led Espresso ON (G), Led Descale ON (O),Led Calc-Clean ON (O),Led Rinsing ON (O),

Led Coffee ON (G).

Legend:

(O) = Orange (G) = Green (R) = Red

TEST MODE Level0

Pressing button Stand-By

TEST MODE Level1

Pressing button Stand-By

TEST MODE Level2

Pressing button Stand-By

TEST MODE Level3

Pressing button Stand-By

TEST MODE Level4

Pressing button Stand-By

TEST MODE Level5

At the start up all loads are turned off. The software allow to have only one load active at the same

time.

Pressing button Stand-By

Start condition: NO BU, NO drag drawer, door open, No

Water sensor

LED INDICATION

Led Espresso

Led Coffee

Blink Alternately

Level 0 (Start Test mode)

Press BUTTON Stand-By to move to the next screen

Start condition:

NO BU, NO drag drawer,

door open and No Water sensor

LED INDICATION

Led

NoBeans

Led

NoWater

Led

GenAlarm

Led Dreg

drawer full

Led

Descale

Led

Rinsing

OFF

Level 1 (Key)

Summary of Contents for 3000 series
















































































Search results

Summary of Contents for 3000 series

Reviews:

Philips 3000 series, Service Manual, Page: 52 / 79

Search results

Summary of Contents for 3000 series

Reviews: