Philips 3000 series Service Manual Download Page 43

Page: 43 / 79

PHILIPS 4000 and 3000 05 SERVICE MODE

2/18

Verify the firmware version

Page 0 (FIRMWARE)

Firmware version on the display.

The machine model is shown ( FOCUS, CLASS or TOP).

The voltage of the main supply “230V”

The frequency of the main supply is shown (50 or 60 Hz)

The firmware version is the same as the label on MicroController

ERROR:

The firmware version is different from the label on MicroController;

change the CPU_POWER Boards !

ERROR:

If in machine model field is written “Unknow” and backlight of display is Yellow, check

the jumper in interface.

The machine passes to the Page 1 (KEYBOARD)

ERROR:

The page does not change; Check the interface

board and the flat cable (JP21)

Press

“ ” to move to the next screen

Page 5

High voltage loads test (Heater , Grinder ):

a) Heater (230V AC)

b) Grinder (320V DC)

The user can change the page by pressing the

button.

Page 0 is accessible only entering Test Mode from power-off mode; at the start up all loads are

turned off.

TEST MODE Level0

TEST MODE Level1

TEST MODE Level2

TEST MODE Level3

TEST MODE Level4

TEST MODE Level5

Pressing button

Summary of Contents for 3000 series
















































































Search results

Summary of Contents for 3000 series

Reviews:

Philips 3000 series, Service Manual, Page: 43 / 79

Search results

Summary of Contents for 3000 series

Reviews: