Philips 3000 series Service Manual Download Page 15

Page: 15 / 79

PHILIPS 4000 and 3000 02 TECHNICAL SPECIFICATIONS

5/5

2.3. Machine parameters and performance

PRODUCT

QUANTITY

Default quantity

(Grams)

User

programmable

Programm. by

Production /

Service

Espresso

40 +/- 10gr

Yes

Espresso lungo

120 +/- 10%

Yes

Classic coffee

Min.145 Max.190

Yes

Hot water

Continues until the water supply has been exhausted (capacitive sensor)

Steam

pannarello

(frother)

Continues until the water supply has been exhausted (capacitive sensor)

Descaling cycle frequency

Hard-

ness

Water hardness

Without water filter

With water filter

Soft (up to 7°dH)

240 litres (480,000 pulses)

480 litres (960,000 pulses)

Medium (7° - 14°dH)

120 litres (240,000 pulses)

240 litres (480,000 pulses)

Hard (15° - 21°dH)

60 litres (120,000 pulses)

120 litres (240,000 pulses)

Very hard (over 21°dH)

30 litres (60,000 pulses)

60 litres (120,000 pulses)

The default water hardness level is 4. Each litre of water corresponds to approximately

2,000 pulses.

In the machines where is not possible change the water hardness the default

hardness level is 3.

WATER TANK

Description

Water reserve (pulses) with water filter

200

Water reserve (pulses) with no water filter

200

Water reserve modifiable by Production/Service

departments

"Fill tank" alarm

Yes

"No tray" alarm

Yes (Fill tank)

Water mains

DREG DRAWER

Description and values

Time-out for dreg drawer

5 sec.

Reset dreg counter

Dreg emptying alarm, if the dreg drawer is

removed for more than 5 seconds.

STANDBY

Description and values

Inlet time (default)

15 minutes

Inlet time programmed by Production/Serv-

ice

Yes

Boiler temperature during Standby

Boiler OFF

Summary of Contents for 3000 series
















































































Search results

Summary of Contents for 3000 series

Reviews:

Philips 3000 series, Service Manual, Page: 15 / 79

Search results

Summary of Contents for 3000 series

Reviews: