Philips 150S4FG/00 Service Manual Download Page 28

Page: 28 / 79

ISP CABLE for CPU

150S4 LCD

Step 1 : Make a folder in your PC as shown in Fig. 3.

For example : C:\ISP_H3HSV200

Step 2 : Copy ISP Software (ISP_H3HSV200.zip) into your folder as

Shown in Fig.3.

Step 3 : Unzip isp.zip into your folder as shown in Fig. 4.

Step 4 : Copy the updated Firmware/ Factory Default data for HS

panel (for example : HSV200 for EEPROM) as shown in Fig.4.

Step 5 : Connect ISP cable between PC and Monitor (B)as shown in

Fig. 5.

Step 6 : Execute ISP Software in Monitor (A) as shown in Fig. 5.

1.=> At DOS command line ,Execute ISP software GP2.exe,

C:\ISP>GP2.exe then the prompt command line appear

AA:2>

2.=>type in AA:2>batch HUDSON.txt ,a group of messages

are shown Fig 6.The execution time is displayed on last line

3.=>After the prompt command line AA:2> appear again,

it means that the update procedure is complete.

4.=>Type exit to exit ISP software.

5.=>Please do AC power OFF , then power ON,To restart CPU.

Remark: for debug

If show [ fail ] in any line, means error binary file name or error

evices file. Pls check HUDSON.txt and confirm file is in directory.

Then execute again.

Attention : Do not power off your system before you finish you

ISP function .

Fig. 4

Fig. 3

Configuration and procedure

ISP (In System Program) software

ISP cable

is provided by Genesis to upgrade

the firmware of flash ROM and Factory default data of EEPROM.

is for the interface between "Parallel Port of PC" and

"15 pin-D-SUB connector of Monitor".

It is a DOS-based program, which

be run in MS-Windows.

cannot

System and equipment requirements

1. An i486 (or above) personal computer or compatible.

2. Microsoft operation system Windows 95/98

4. ISP Cable (3138 106 10213) as shown in Fig. 1

5. Set up PC Monitor as shown in Fig. 2

DOS environment

3. ISP Software (Please use latest version from philips)

Fig. 1 => ISP CABLE : 12nc is "3138 106 10213.

Fig. 2

Rear view of the monitor

video

card

Video cable

Connect to

Mains cord

Monitor (A)

Fig. 6

Connect to

Mains cord

Rear view of Hudson3

printer

port

TP1)

D-Sub

video

card

Video cable

Monitor (A)

Monitor (B)

Fig. 5

Go to cover page

Summary of Contents for 150S4FG/00
















































































Search results

Summary of Contents for 150S4FG/00

Reviews:

Philips 150S4FG/00, Service Manual, Page: 28 / 79

Search results

Summary of Contents for 150S4FG/00

Reviews: