Philips 104S11/00 Service Manual Download Page 50

Page: 50 / 74

Mechanical Instructions

104S CM23 GSIII

Fig. 1

lid

lids

screws

Fig.3

Fig.2

0. General

2. Video panel

3. Main panel

To be able to perform measurements and repairs on the "circuit

boards", these unit should placed in the service position first.

1. Remove the rear cover

- Open two lids with "-" type screwdriver. Refer to fig2 and fig3.

- Remove 4 screws with "+" type screwdriver.

- Remove the metal shielding on rear side of Video panel by

desolder lags of metal shielding.

- Disconnect the degaussing coil from Main panel.

- Remove the video panel from CRT.

- Remove the "screw" of I/F cable from Main panel.

- Disconnect the CRT ground "1701" from Video panel.

- Disconnect the Hi-Pot cap from CRT.

- Disconnect the yoke wire connector "1601" from Main panel.

- Slide the main panel out of bottom tray.

- Place Main panel in service position as shown in Fig.1.

- Mount Video panel again on CRT.

- To connect Hi-Pot cap again.

- To connect "1701" again.

- To connect the yoke wire "1601" again.

Go to cover page

Forward

Back

Summary of Contents for 104S11/00











































































Search results

Summary of Contents for 104S11/00

Reviews:

Related manuals for 104S11/00

Brands by name

Popular brands

Philips 104S11/00, Service Manual

Search results

Summary of Contents for 104S11/00

Reviews:

Related manuals for 104S11/00

Brands by name

Popular brands