PHILIPS Respironics OmniLab Advanced + Clinical Manual Download

Page: 5 / 52

Section 1: Introduction

1.1 Package Contents

The OmniLab Ad system may include the following components. Some components are optional accessories
that may not be packaged with the device.

OmniLab Ad device

Power cord retainer and screw

Humidifier (optional)

AC power adapter

Clinical manual

Reusable gray foam filter

Flexible tubing (1.8 m x 22 mm)

Disposable white ultra-fine filter

Power cord

SD card (optional)

1.2 Intended Use

The OmniLab Ad is intended to provide non-invasive ventilation for pediatric patients 7 years or older

>18.2 kg (40 lbs) with Respiratory Insufficiency or Obstructive Sleep Apnea (OSA). It is also intended to treat adult
patients >30 kg (66 lbs) with Respiratory Insufficiency or Obstructive Sleep Apnea caused by central and/or mixed

apneas and periodic breathing. The device is intended for use in the hospital.

WARNING: The effectiveness of the A-Flex, Bi-Flex, C-Flex, C-Flex+ or AVAPS therapy features or the autoSV

mode has not been established for pediatric patients at this time.

Summary of Contents for OmniLab Advanced +




















































Search results

Summary of Contents for OmniLab Advanced +

Reviews:

Related manuals for OmniLab Advanced +

Brands by name

Popular brands

PHILIPS Respironics OmniLab Advanced +, Clinical Manual

Search results

Summary of Contents for OmniLab Advanced +

Reviews:

Related manuals for OmniLab Advanced +

Brands by name

Popular brands