– 6 –
EN
Setup
SETUP > AUDIO >
DOLBY DIGITAL
Connecting to a Dolby Digital decoder
for Dolby Digital audio output.
BITSTREAM
Connecting to other equipment (an MD
deck or DAT deck etc.)
without Dolby Digital decoder.
PCM
Connection
Setting
Hint for Cable Box or Satellite Box
L
R
VCR
DVD/VCR
AUDIO OUT
L
R
DIGITAL
AUDIO OUT
or
AUDIO
OUT
DVD
S-VIDEO
OUT
COMPONENT
VIDEO OUT
L
R
Stereo system
Method 1
Analog audio
input jacks
AUDIO OUT
(Analog)
Connection to an Audio System
Audio cable
(supplied)
* To complete these settings, refer to pages 20-21.
Hint
• The audio source on a disc in a Dolby Digital Multi channel surround
format cannot be recorded as digital sound by an MD or DAT deck.
• By hooking this unit up to a Multi channel Dolby Digital decoder, you
can enjoy high-quality Dolby Digital Multi channel surround sound as
heard in the movie theaters.
• Playing a DVD using incorrect settings may generate noise distortion
and may also damage the speakers.
(DVD mode only)
Digital audio
input jack
DIGITAL
AUDIO OUT
Audio Coaxial Digital cable
(commercially available)
Method 2
Dolby Digital decoder,
MD deck or DAT deck
Setup
If channel 3 has been already occupied for
broadcasting,
1) Set your TV to channel 4.
2) Insert a pre-recorded tape into this unit.
3) Press
[SOURCE]
on the unit so that the VCR
SOURCE light is lit.
•
If noise appears on the TV screen, press
[VCR/
TV]
on the remote control.
4) Press
[PLAY
B
]
once.
5) After a few seconds, press and hold
[PLAY
B
]
on the unit for 3 seconds.
• The RF output channel will change to chan-
nel 4 from channel 3 and you will see a
playback picture.
• When a picture does not appear on the TV
screen, repeat step 4.
6) Press
[STOP
C
]
to stop playback.
RF Output Channel
Connections
Hint
• The RF output channel does not
change when you adjust tracking
during playback. In case RF output
channel changes, you can easily
switch it back. Start the playback
again then press and hold
[PLAY
B
]
on the unit for 3 seconds.
Select this connection when you want to view or record a
scrambled channel. With this connection, channels cannot be
changed on the unit. You can view or record ONLY the channels you
have selected on the cable box or the satellite box.
• While you are recording, only the recorded channel can be viewed.
To select channels of the cable box or satellite box
1) Turn on the unit by pressing
[STANDBY-ON]
, then press
[VCR/TV]
. The STANDBY-ON indicator on the front panel will
light, then press
[SKIP/CH.
G
/
K
,
H
/
L
]
to select channel 3
or 4 (the same channel as the output channel of the cable box
or satellite box).
• If you use the channel 4, you need to change the unit’s RF
output to channel 4. Refer to “RF Output Channel”.
2) At the TV, select channel 3 or 4 (the same channel as you have
selected at step 1).
3) On the cable box or satellite box, select the channel you want
to view or record.
ANT-OUT
ANT-IN
RF cable
(supplied)
(Back of DVD/VCR)
IN
OUT
(Back of TV)
Satellite or
Cable TV
signal
(Cable box or
Satellite box)
Please refer to “Basic TV Connection” on the front page before you use this unit.
Audio
DVD/VCR
DIGITAL
AUDIO OUT
COAXIAL
AUDIO
OUT
DVD
S-VIDEO
OUT
COMPONENT
VIDEO OUT
COAXIAL
E8C1UCD_EN.indd 6
E8C1UCD_EN.indd 6
2007/04/03 9:48:54
2007/04/03 9:48:54
