background image

Phason 

 

VTC-1D user manual 

11140010  

 

Wiring the VTC-1D 

1.

 

Set the voltage switch 

to the correct position for 

the line voltage used. 

2.

 

Set jumper 

E

 to the correct position for the 

temperature units (Fahrenheit or Celsius) you want 
to use.  

3.

 

Connect the incoming power and load wires as 
shown in the diagram. 

 

Connecting the temperature probe  

Follow the guidelines below and connect the 
temperature probe as shown in the diagram.  

‹

 

Do not run the probe cable in the same conduit as 
AC power cables  

‹

 

Do not run the sensor cable beside AC power 
cables or near electrical equipment. 

‹

 

When crossing other cables or power lines, cross 
them at a 90 degree angle. 

 

Using four-zone averaging 

The VTC-1D can monitor the temperature in four 
different zones. The control takes an average of the four 
temperatures and operates according to the average 
temperature.  

To use four-zone averaging, you must connect four 
temperature sensors to the unit. Connect the probes as 
shown to the right. 

 

Extending probe cables 

You can extend temperature probe cables to lengths of up to 500 feet. Follow the temperature probe 
guidelines and the guidelines below when extending cables. 

‹

 

Use two-wire 18 AWG jacketed cable. Phason recommends Belden # 9408, Alpha # 5052, or an 
equivalent. Extension cable is also available from Phason. For more information, contact your dealer or 
Phason. 

‹

 

If the unit operates erratically with the extended probe, run the cable along a different path or shorten it. 

Service

box

Enclosure

I

A

Probe

Insulate 
using a 

#31 wire 
nut or 
similar 
connector

Line/L1 

Neutral/L2 

Black

A

Fuse: 15 A, 250 VAC ceramic

B

Important:

A suitable switch must be installed between the control 

and the motor.  

Important:

 Il est essentiel qu’un interrupteur convenable soit installé 

entre le contrôle et le moteur.

C

Caution:

For controlling shaded-pole, permanent-split-capacitor, or 

universal motors only. 

Caution:

 Destiné uniquement à la commande de moteurs universels. 

À bague de déphasage ou à condensateur permanent. 

Connect all ground wires to the grounding terminal located near the 
cable entry points. 

E

11150502

Use liquid-tight connectors at the cable entry points and seal with an 
RTV silicone. 

C

Before connecting the power, set 

the switch to the correct setting 

230 VAC 

115 

230 

F

G

Temperature 
differential set 

White

Blue

20°F

1°F

115 VAC

B

D

E

Fan 

Off set-back/idle 
set mode 

16°F 

1°F 

idle mode 

I

H

Fahrenheit

Celsius 

Summary of Contents for VTC-1D













Reviews: