background image

16

Step 4. Use

Now press ALL three buttons on the controller at the same time.

Pressing this button reduces the flow setting by 10.

The controller will indicate this reduction:

If the pairing is successful the LED segments will stop circling and the ‘Fob’ will 

disappear from the controller display. Your fob should now operate the controller as 

described in 

1. Fob Overview

.

If the pairing is unsuccessful turn the controller off for 30 seconds then on again and 

repeat the steps above.

Pressing this button increases the flow setting by 10.

The controller will indicate this increase:

Step 4. Use Cont’d

Pressing and holding this button will start an auto calibration on your controller. 

(Ensure flow is set to your desired value e.g. 50).

All LEDs on the segment light to show auto calibration has started, the controller 

will indicate ‘AUt’.

When the controller has calibrated one LED on the segment will light to show 

this. ‘CAL’ will disappear from the controller display.

Pressing this button starts and stops the pump. If the pump is running press the 

button once to stop. All LEDs on the segment will light, the pump will stop and 

controller indicates ‘StP’.

If the pump is stopped press the button once to start.

A single LED on the segment will light, the pump will start and controller indi-

cates the current flow. e.g. ‘30’.

Summary of Contents for Shadow RODI-40 Manual





























Reviews: