Pfeiffer TC 110 PB, Operating Instructions Manual

Page: 22 / 37

22
The Pfeiffer Vacuum parameter set
7.2.6 Set value settings
7.3 Configuring the connections
The electronic drive unit is pre-configured in the factory. Thereby the turbopump is im-
mediately operational with the necessary functions. The connections of the electronic
drive unit can be configured to suit individual requirements using the parameter set.
7.3.1 Digital outputs on "X3"
 Configuration via parameters
[P:019]
and
[P:024]
.
316 DrvPower Drive power 1 R W 0 999999
319 PumpCycles Pump cycles 1 R 0 65535 x
326 TempElec Temperature electronic 1 R °C 0 999999
330 TempPmpBot Temperature pump bottom part 1 R °C 0 999999
336 AccelDecel Acceleration / Deceleration 1 R rpm/s 0 999999
342 TempBearng Temperature bearing 1 R °C 0 999999
346 TempMotor Temperature motor 1 R °C 0 999999
349 ElecName Name of electronic drive unit 4 R
354 HW Version Hardware version electronic drive unit 4 R
360 ErrHist1 Error code history, pos. 1 4 R x
361 ErrHist2 Error code history, pos. 2 4 R x
362 ErrHist3 Error code history, pos. 3 4 R x
363 ErrHist4 Error code history, pos. 4 4 R x
364 ErrHist5 Error code history, pos. 5 4 R x
365 ErrHist6 Error code history, pos. 6 4 R x
366 ErrHist7 Error code history, pos. 7 4 R x
367 ErrHist8 Error code history, pos. 8 4 R x
368 ErrHist9 Error code history, pos. 9 4 R x
369 ErrHist10 Error code history, pos. 10 4 R x
397 SetRotSpd Set rotation speed (rpm) 1 R rpm 0 999999
398 ActualSpd Actual rotation speed (rpm) 1 R rpm 0 999999
399 NominalSpd Nominal rotation speed (rpm) 1 R rpm 0 999999
# Display Designation Functions
Dat
a
t
y
p
e
Acc
ess
Unit min max default

# Display Designation Functions
Da
ta
ty
pe
Ac
ces
s
metho
d
Unit min max default

700 RUTimeSVal Set value run-up time 1 RW min 1 120 8 x
701 SpdSwPt1 Rotation speed switchpoint 1 1 RW % 50 97 80 x
707 SpdSVal Set value in rot. speed setting mode 2 RW % 20 100 65 x
708 PwrSVal Set value power consumption 7 RW % 10 100
100
1 x
710 Swoff BKP Switching off threshold backing pump in intermit-
tend mode
1 RW W 0 1000 0 x
711 SwOn BKP Switching on threshold backing pump in intermit-
tend mode
1 RW W 0 1000 0 x
717 StdbySVal Set value rotation speed at standby 2 RW % 20 100 66.7 x
719 SpdSwPt2 Rotation speed switchpoint 2 1 RW % 5 97 20 x
720 VentSpd Venting rot. speed at delayed venting 7 RW % 40 98 50 x
721 VentTime Venting time at delayed venting 1 RW s 6 3600 3600 x
730 PrsSwPt 1 Pressure switchpoint 1 10 RW hPa x
732 PrsSwPt 2 Pressure switchpoint 2 10 RW hPa x
739 PrsSn1Name Name sensor 1 4 R
740 Pressure 1 Pressure value 1 10 RW hPa x
742 PrsCorrPi 1 Correction factor 1 2 RW x
749 PrsSn2Name Name sensor 2 4 R
750 Pressure 2 Pressure value 2 10 RW hPa x
752 PrsCorrPi 2 Correction factor 2 2 RW x
777 NomSpdConf Nominal rotation speed confirmation 1 RW Hz 0 1500 0 x
797 RS485Adr RS-485 device address 1 RW 1 255 1 x
1. depending on the pump type
Option Description
0 = Rotation speed switchpoint attained Active, if switchpoint attained
1 = No error Active, if failure-free operation
2 = Error Active, if error message is active
3 = Warning Active, if warning message is active