background image

Connection "Profibus"

15

5.3.4

control-/status byte

5.3.5

Parameterization data

To set a configuration that deviates from the delivery state (="start-up configuration") or 
to define actions in the Profibus "fail-safe" state and/or when response monitoring lapses 
(e.g. master fails) (="fail-safe action"), up to six parameters, described with predefined 
values on a case-by-case basis, can be defined for all modules. Eight-byte parameter-
ization data are added per parameter in the following format (undefined points to be as-
signed 0):

5.4

Expanded diagnostics data

*Device errors and warnings are anchored in the electronic drive unit 

(see p. 33, chap. 

9.3)

.

** see PPO1

Bit

Output data (1 byte)

Input data (1 byte)

7

Error acknowledgement, -> automatic trip 
switch (switching back on only by pumping sta-
tion off and back on)

Warning, general

6

Standby

Warning, temperature

5

Enable venting

Operation: No error, pumping station and motor 
pump are on, no automatic trip switch

4

Heating

Rotation speed switch point attained

3

-

Errors

2

Enable process data (control byte):
0 = ignore
1 = accept

0

1

-

Pump rotates

0

Pumping station

Set rotation speed attained

Byte

Description

0, bit 7

0: Parameter for "start-up configuration"
1: Parameter for "fail-safe action"

0, bit 6

0: Parameter value is integer
1: Parameter value rounded to nearest number to IEEE 754

2-3

Parameter number

4-7

Parameter value

Designation

Example of module designation

Module without additional parameter

PPO1, PPO3, control-/status word, control-/status byte

Module with one to six additional parame-
ters

PPO1 (1 prm) ... (6prm)
PPO1 (1 prm) ... (6prm)
control-/status word (1 prm) ... (6prm)
control-/status byte (1 prm) ... (6prm)

Byte

Designation

Description

1-6

Standard diagnostics Profibus

Defined by Profibus specification

7

Length of the external diagnostics data

8-36

Reserved

37-38 Current error code

0: No error
1-999: Device error*
1001-1999: Device warning 1-999*
2000: Unrecognised module
3xxx: Parameterization data incorrect in accor-
dance with error number in the parameter chan-
nel**

39-69 Internal state

Summary of Contents for TC 110 PB






































Reviews: