Pfaff 3734-2/01 Instruction Manual Download

Page: 3 / 80

Contents

Contents ............................................................................... Chapter - Page

Safety ........................................................................................................................ 1 - 1

.01

Directives ................................................................................................................... 1 - 1

.02

General notes on safety ............................................................................................. 1 - 1

.03

Safety symbols .......................................................................................................... 1 - 2

.04

Important points for the user ..................................................................................... 1 - 2

.05

Operating and specialist personnel ............................................................................ 1 - 3

.05.01

Operating personnel ................................................................................................... 1 - 3

.05.02

Specialist personnel ................................................................................................... 1 - 3

.06

Danger ....................................................................................................................... 1 - 4

Proper use ................................................................................................................. 2 - 1

Specifications ........................................................................................................... 3 - 1

.01

PFAFF 3734-2/01; -2/21 .............................................................................................. 3 - 1

.02

Model, needles and threads ....................................................................................... 3 - 1

Disposal of machines ............................................................................................... 4 - 1

Transport packaging and storage ........................................................................... 5 - 1

.01

Transport to the customer’s premises ....................................................................... 5 - 1

.02

Transport within the customer’s premises ................................................................ 5 - 1

.03

Disposal of the packaging .......................................................................................... 5 - 1

.04

Storage ...................................................................................................................... 5 - 1

Explanation of the symbols

.....................................................................................

6 - 1

Controls .................................................................................................................... 7 - 1

.01

On/off switch ............................................................................................................. 7 - 1

.02

Pedal .......................................................................................................................... 7 - 1

.03

Knee switch ............................................................................................................... 7 - 2

.04

Lever for lifting the roller presser ............................................................................... 7 - 2

.05

Control panel .............................................................................................................. 7 - 3

.05.01

Displays on the screen ............................................................................................... 7 - 3

.05.02

Key functions ............................................................................................................. 7 - 3

Mounting and commissioning the machine .......................................................... 8 - 1

.01

Mounting .................................................................................................................... 8 - 1

.01.01

Adjusting the table-top height .................................................................................... 8 - 1

.01.02

Fitting the tilt lock ....................................................................................................... 8 - 2

.01.03

Adjusting the V-belt tension ....................................................................................... 8 - 2

.01.04

Mounting the synchronizer ......................................................................................... 8 - 3

.01.05

Mounting the spool holder ......................................................................................... 8 - 3

.01.06

Attaching the earthing wire / connecting the plug connections .................................. 8 - 4

.02

Commissioning .......................................................................................................... 8 - 4

.03

Switching the machine on/off .................................................................................... 8 - 4

Summary of Contents for 3734-2/01

















































































Search results

Summary of Contents for 3734-2/01

Reviews:

Related manuals for 3734-2/01

Brands by name

Popular brands

Pfaff 3734-2/01, Instruction Manual

Search results

Summary of Contents for 3734-2/01

Reviews:

Related manuals for 3734-2/01

Brands by name

Popular brands