Permobil Chairman Playman Service Manual Download Page 13 | Manualshive

Page: 13 / 28

background image

13

Magnetic brakes

Fitting

1.

Use the adjusting screws to adjust the
magnetic brake. Set both screws flush with
back surface of the brake, then turn the screws
downwards 1 1/4 turns, see fig. 18.

2.

Fit the brake disc into the magnetic brake.

3.

Fit the cover.

Fig. 19. Adjusting the magnetic brake using the

two adjusting screws.

Fig. 20. Magnetic brake, brake disc and cover

removed.

Fig. 21. Magnetic brake, brake disc

and cover fitted.

«
...
11
12
13
14
15
...
»

Summary of Contents for Chairman Playman





























Reviews:

No comments

Related manuals for Chairman Playman

Brand: M2 Shower Chairs Pages: 7

Brand: Quickie Pages: 36

progeo BASIC LIGHT

Brand: Rehateam Pages: 22

Brand: Vanraam Pages: 38

Brand: Otto Bock Pages: 32

Brand: Otto Bock Pages: 72

Brand: Otto Bock Pages: 172

multi frame Series

Brand: R82 Pages: 32

Brand: Anatomic SITT Pages: 28

Zitzi Delfi Pro

Brand: Anatomic SITT Pages: 48

Brand: Pride Pages: 12

Brand: XXL-Rehab Pages: 24

Brand: Safer Locks Pages: 28

S-Ergo 105(KM-1500?3)

Brand: Karman Healthcare Pages: 32

Brand: Days Pages: 8

Brand: AAT Pages: 36

146-STD22ECDDA-SF

Brand: McKesson Pages: 2

Brand: Etac Pages: 4

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands