manualshive.com logo in svg

PerkinElmer OilExpress System, User Manual

Share
Download
PerkinElmer OilExpress System User Manual Download Page 48

48 . OilExpress System User's Guide 

6.

 

Push the needle tubing over the shorter end of the needle (to a minimum of 25 mm,  

1 inch). 

7.

 

Loosen the Allen screw on the insulation block. Install the insulation block on the Z-rack 

with the insulation block sleeve facing down and the insulation block (black coax) cable 

on the left side. Ensure that the insulation block cable is not twisted. 

8.

 

Push the insulation block onto the Z-rack until firmly seated.  

9.

 

With an Allen wrench, tighten the insulation block set screw until it makes contact with 

the flat portion of the Z-rack. Do not overtighten the setscrew. 

Connecting the tubing to the solvent bottle 

1.

 

Thread the tubing from top to bottom through the cap of the wash bottle as shown in 

Figure 23.  

 

Figure 23 Connecting the solvent tubing 

2.

 

Fill the solvent bottle with solvent. 

3.

 

Screw the cap on to the solvent bottle securely. 

4.

 

Position the bottle safely, behind the instrumentation at a location where it will not be 

accidentally knocked. 

Solvent bottle lid 

Solvent bottle 

Summary of Contents for OilExpress System







































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands