•
DRESS PROPERLY.
Do not wear loose clothing, gloves, neckties, or jewelry. They can get caught and draw you into moving
parts. Rubber gloves and nonskid footwear are recommended when working outdoors. Also wear protective hair covering to
contain long hair.
•
ALWAYS
wear safety goggles that comply with United States ANSI Z87.1 and a face shield or dust mask if operation is dusty.
Everyday eyeglasses have only impact-resistant lenses, they are
NOT
safety glasses.
•
SECURE WORK.
Use a clamps or vice to hold workpiece when practical. It’s safer than using your hand and frees both hands
to operate tool.
•
DON’T OVERREACH.
Keep proper footing and balance at all times.
•
MAINTAIN TOOLS WITH CARE.
Keep tools sharp and clean for better and safer performance. Follow instructions for
lubricating and changing accessories.
•
DISCONNECT TOOLS.
When not in use, before servicing, or when changing attachments, blades, bits, cutters, etc., all tools
should be disconnected.
•
AVOID ACCIDENTAL STARTING.
Be sure switch is off when plugging in any tool.
•
USE RECOMMENDED ACCESSORIES.
Consult the operator’s manual for recommended accessories. The use of improper
accessories may risk injury.
•
NEVER STAND ON TOOL.
Serious injury could occur if the tool is tipped or if the cutting tool is unintentionally contacted.
•
CHECK DAMAGED PARTS.
Before further use of the tool, a guard or other part that is damaged should be carefully
checked to determine that it will operate properly and perform its intended function. Check for alignment of moving parts, binding
of moving parts, breakage of parts, mounting and any other conditions that may affect its operation. A guard or other part that is
damaged must be properly repaired or replaced by an authorized service center to avoid risk of personal injury.
•
USE THE RIGHT DIRECTION OF FEED.
Feed workpiece into a blade or cutter against the direction of rotation of blade or
cutter only.
•
NEVER LEAVE TOOL RUNNING UNATTENDED. TURN THE POWER OFF.
Don’t leave tool until it comes to a complete stop.
•
PROTECT YOUR LUNGS.
Wear a face or dust mask if the cutting operation is dusty.
•
PROTECT YOUR HEARING.
Wear ear plugs or muffs during extended periods of operation.
•
DO NOT ABUSE CORD.
Never yank cord to disconnect from receptacle. Keep cord away from heat, oil, and sharp edges.
•
WHEN OPERATING A POWER TOOL OUTSIDE, USE AN OUTDOOR EXTENSION CORD MARKED “W-A” OR “W”.
These
cords are rated for outdoor use and reduce the risk of electric shock.
•
ALWAYS KEEP THE BLADE GUARD AND SPREADER (RIVING KNIFE) IN PLACE
and in working order.
•
KEEP BLADES CLEAN, SHARP, AND WITH SUFFICIENT SET.
Sharp blades minimize stalling and kickback.
•
KEEP HANDS AWAY FROM CUTTING AREA.
Keep hands away from blades. Do not reach underneath work or around or
over the blade while blade is rotating. Do not attempt to remove cut material when blade is moving.
•
BLADE COASTS AFTER BEING TURNED OFF.
•
NEVER USE IN AN EXPLOSIVE ATMOSPHERE.
Normal sparking of the motor could ignite fumes.
•
INSPECT TOOL CORDS PERIODICALLY.
If damaged, have repaired by a qualified service technician at an authorized service
facility. The conductor with insulation having an outer surface that is green with or without yellow stripes is the
equipment-grounding conductor. If repair or replacement of the electric cord or plug is necessary, do not connect the
equipment-grounding conductor to a live terminal. Repair or replace a damaged or worn cord immediately. Stay constantly aware
of cord location and keep it well away from the rotating blade.
•
INSPECT EXTENSION CORDS PERIODICALLY
and replace if damaged.
•
GROUND ALL TOOLS.
If tool is equipped with three-prong plug, it should be plugged into a three-hole electrical receptacle.
•
CHECK WITH A QUALIFIED ELECTRICIAN
or service personnel, if the grounding instructions are not completely understood,
SAFETY INSTRUCTIONS
_ 6 _
