Pepwave BR1 Slim User Manual Download Page 124 | Manualshive

Page: 124 / 154

background image

http://www.pepwave.com

124

Copyright @ 2014 Pepwave

22.2 Firmware Upgrade

The firmware of thePepwave MAX is upgradeable through Web Admin Interface.

Firmware upgrade functionality is located at

System> Firmware

:

There are two ways to upgrade the unit. The first method is online firmware upgrade.The system can
Check,Download and Upgrade over the Internet.The second method is to upload a firmware file manually.

Click on the

Check again

button to use online upgrade. With online upgrade, Pepwave MAX checks

online for new firmware.If a new firmware is available, the Pepwave MAX will automatically download the
firmware. The upgrade process will subsequently be automatically initiated.

You may also download a firmware image from the

Pepwave web site

and update the unit manually.Click

Browse

to select the firmware file from the local computer, and then click

ManualUpgrade

to send the

firmware to the Pepwave MAX.The Pepwave MAX will then automatically initiate the firmware upgrade
process.

Please note that all Pepwave devices are equipped to be able to store two different firmware versions in
two different partitions. A firmware upgrade preformed will always replace the inactive partition. If you
want to keep the inactive firmware, you can simply reboot your device with the inactive firmware and then
perform the firmware upgrade.

Important Note

The firmware upgrade process may not necessarily preserve the previous configuration, and the behavior varies
on a case-by-case basis. Consult the Release Notes for the particular firmware version.
Do not disconnect the power during firmware upgrade process.
Do not attempt to upload a non-firmware file, or a firmware file that is not qualified, or not supported, by Pepwave.
Upgrading a Pepwave MAX with an invalid firmware file will damage the unit, and may void the warranty.

Important Note

If the firmware is rolled back from 5.x to 4.x, the configurations will be lost.

«
...
122
123
124
125
126
...
»

Summary of Contents for BR1 Slim



























































































































































Reviews:

No comments

Related manuals for BR1 Slim

Brand: Abocom Pages: 1

S5120V3-EI Series

Brand: H3C Pages: 54

Brand: H3C Pages: 116

Protege PRT-PX16-PCB

Brand: ICT Pages: 34

ADSL 2/2+ VPN Firewall Router ADE-4300A/B

Brand: Planet Pages: 132

Brand: EMCIS Pages: 14

Net2Air Ins-40085-US

Brand: Paxton Pages: 4

Brand: ZyXEL Communications Pages: 215

Brand: NKE Pages: 15

PSoC 4 S Series

Brand: Cypress Pages: 4

Brand: ADIC Pages: 140

Brand: Comtrend Corporation Pages: 4

Brand: Linksys Pages: 6

Brand: MaxComm Pages: 10

Brand: Handicare Pages: 60

Brand: Zalip Pages: 76

Brand: ADTRAN Pages: 20

Brand: Alcatel Pages: 4

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands