background image

P R O F I B U S   P

O W E R

  H

U B

  S

E G M E N T

  C

O U P L E R

Safety

Subject to reasonable modifications due to technical advances.

Copyright Fuchs, Printed in Germany

Fuchs Group • Tel.: G49 621 776-0 • USA +1 330 4253555 • Sin65 67799091 • Internet http://www.pepperl-fuchs.com

7

Dat

e

 of

 I

ssue 

24.

3.

11

The corresponding data sheets, the declaration of conformity, the EC-
type-examination certificate and applicable certificates (see data sheet)
are an integral part of this document. You can find this information under
www.pepperl-fuchs.com.

1.5

Delivery, Transport and Storage

Check the packaging and contents for damage. 

Check if you have received every item and if the items received are the
ones you ordered. 

Keep the original packaging. Always store and transport the device in
the original packaging.

Always store the device in a clean, dry environment. Note the permitted
storage temperature (see data sheet).

1.6

Marking

Gateway motherboards

Gateway module

MB-FB-GT

Fuchs GmbH

Gateway motherboard

Declaration of Conformity

TÜV 04 ATEX 2500X

 Ex II 3G EEx nA IIC T4

MB-FB-GTR

Fuchs GmbH

Redundant gateway motherboard

Declaration of Conformity

TÜV 04 ATEX 2500X

 Ex II 3G EEx nA IIC T4

HD2-GTR-4PA

Fuchs GmbH

Gateway module

Declaration of Conformity

TÜV 04 ATEX 2500X

 Ex II 3G EEx nA IIC T4

Summary of Contents for HD2-GTR-4PA





















































































Reviews: