manualshive.com logo in svg

Pepperl+Fuchs HD2-GTR-4PA, Manual, Page: 57 / 84

Share
Download
Pepperl+Fuchs HD2-GTR-4PA Manual Download Page 57

P R O F I B U S   P

O W E R

  H

U B

  S

E G M E N T

  C

O U P L E R

Advanced Diagnostics with the PROFIBUS Power Hub

Subject to reasonable modifications due to technical advances. 

Copyright Fuchs, Printed in Germany

Fuchs Group • Tel.: G49-621-776-0 • USA +1-330-4253555 • Sin65-67-799091 • Internet www.pepperl-fuchs.com

57

Dat

e

 of

 I

ssue 

24.

3.

11

•

Figure 7.1: Schematic topology of direct connection of diagnostics

Hardware

Description

Segment 1...4

PROFIBUS PA segments

HD2-DM-A

Advanced Diagnostic Module (ADM) on 
Fieldbus Power Hub Motherboard.

HD2-GTR-4PA

Gateway Module on Gateway Motherboard.

Operator / Maintenance 
Application

Depending on setup and structure, FDT can 
either run on the maintenance application or 
the operator application.

Software

Description

FDT
(Field Device Tool)

The FDT specification defines the interaction 
of DTMs with host computers or software. An 
FDT frame application is a PC-based soft-
ware including many DTMs for configuration 
monitoring and programming of field devices. 
Both the Diagnostic Manager DTM and the 
Gateway DTM run in an FDT environment.

HD2-DM-E

Segment 1

Segment 2

Segment 3

Segment 4

Segment 1

Segment 2

Segment 3

Segment 4

PROFIBUS DP

PROFIBUS 

Power Hub  

Motherboard

PROFIBUS P

A

HD2-DM-A

FDT Frame

DTM

Diagnostic Manager

HD2-DM-E

Gateway  

Motherboard

HD2-GTR-4PA

DTM

HD2-GTR-4PA

Operator / Maintenance Application

Summary of Contents for HD2-GTR-4PA





















































































Reviews:

No comments